Howto:Arcor-IP Anlagenanschluss - Arcor - SIP Testreport

From innovaphone wiki
Jump to navigation Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.

Innovaphone Compatibility Test Report

Summary

SIP Provider: Arcor

The provider supports all required innovaphone features and is therefore qualified as recommended SIP Provider.

Arcor does not support the T.38 protocol, therefore you cannot send faxes using this SIP trunk.

That beeing said, the provider has achieved 87% of all possible test points. For more information on the test rating, please refer to Test Description

  • Features:
    • Direct Dial In
    • DTMF
  • Supported Codecs by the provider
    • G711
    • G729

Certification Status

Recprod.PNG The tests for this product have been completed and it has been approved as a recommended product (Certification document).

Testing of this product has been finalized August 20th, 2008.

Testing Enviroment

Scenario

This scenario tries to be as simple as possible. The IP - PBX and the phones are all in the same network, having public IP - adresses. The signalling channel will pass through the PBX, the media channel will go from endpoint (phone) to endpoint (provider).

CompatProviderSIP-1.JPG

Test Results

For more information on the test procedure, please read the following wiki article: SIP Interop Test Description. Bold lines in the test results indicate a KO-criteria.

Basic Call

Tested feature Result
call using g711a Yes
call using g711u Yes
call using g723 No
call using g729 Yes
Overlapped sending No
early media channel Yes
Fax using T.38 No
CGPN can be supressed No
Reverse Media Negotiaton Yes
Voice Quality OK? Yes

Direct Dial In

Tested feature Result
Inbound(Provider -> Innovaphone) Yes
Outbound(Innovaphone -> Provider) Yes

DTMF

Tested feature Result
DTMF tones sent correctly Yes
DTMF tones received correctly Yes

Hold/Retrieve

Tested feature Result
Call can be put on hold Yes
Held end hears music on hold / announcement from PBX Yes
Held end hears music on hold / announcement from provider N/A

Transfer with consultation

Tested feature Result
Call can be transfered Yes
Held end hears music on hold Yes
Call returns to transferring device if the third

Endpoint is not available

Yes

Transfer with consultation (alerting only)

Tested feature Result
Call can be transfered Yes
Held end hears music on hold or dialing tone Yes
Call returns to transferring device if the third

Endpoint is not available

Yes

Blind Transfer

Tested feature Result
Call can be transfered Yes
Held end hears dialing tone No

Broadcast Group & Waiting Queue

Tested feature Result
Caller can make a call to a Broadcast Group Yes
Caller can make a call to a Waiting Queue Yes
Announcement if nobody picks up the call Yes

Configuration

Firmware version

All innovaphone devices use V6 SR2 HF7 as firmware.

SIP - Trunk

First of all the SIP Trunk must be configured. Since Arcor authenticates a user account only by IP - Address, you cannot use the normal SIP-Gateway object. You need to configure a GW without registration and route the calls to the PBX.

Arcor-IP Anlagenanschluss - Arcor - SIP Testreport 1.PNG

Number Mapping

Arcor-IP Anlagenanschluss - Arcor - SIP Testreport 2.PNG

Route Settings

Because Arcor, as most SIP - Providers too, doesn't support overlap sending, you must enable the blockwise sending of the phone number. You can do this by enabling Force enblock in your routes.

The second setting you must check is Interworking(QSIG,SIP). This feature must be enabled to properly relay suplementary services, like Hold over the SIP Trunk. If this checkbox is unchecked only basic call Information like connect and disconnect will be forwarded by the Gateway.

Arcor-IP Anlagenanschluss - Arcor - SIP Testreport 3.PNG


Configuration 2017 Arcor/Vodafone

Firmware version

12r1 sr11

SIP-Trunk

http://wiki.innovaphone.com/img_auth.php/e/ee/1siptrunk.png

Number Mapping

http://wiki.innovaphone.com/img_auth.php/8/8a/2numberplan.png

Route Settings

http://wiki.innovaphone.com/img_auth.php/7/7f/3routes.png

At the last Point (-> SIP1:VodafoneSIP) add the UUI: <sip:+49789123450@DOMAIN-FROM-ARCOR;user=phone>