Howto:How to Reset IPXXX

From innovaphone-wiki

Jump to: navigation, search

Contents

Summary

Different Reset Options of IPXXX

Applies To

This information applies to

  • All innovaphone products with the latest boot code.

More Information

Different options resetting innovaphone devices.

  • bringing to Factory default
  • bringing to TFTP mode for GWLoad
  • clearing config
  • explaining the LED behavior

Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230, IP240

Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table. If you want to reanimate this devices now with GWLoad, do not powercycle the device again. If the factory reset was successful the device is now in the defined TFTP-Mode and ready for GWLoad. If you just wanted to factory reset the device you can do a powercycle for sure.

If the factory reset was not successful please contact rma@innovaphone.com

or look at Howto:Get Access to Gateways if the Assistant don't boot the device.


Device (visual display) Reset Button/Key Button pressed Clear Config

Firmware Boot code update

Pressing Button to TFTP without deleting config in seconds ca. Pressing Button to factory reset in seconds ca. GWLoad- / TFTP-Mode Firmware starting Firmware ready Firmware Error
IP21

(all LED's)

Button ready: <5s blink, >5s constant flash

line1 + line2 + door + aux constant flash / link + act off

with plugged in ethernet cable 100M + link: <3s off, >3s normal operating state

...

ready fast blink, line1 + line2 + door + aux off link + 100M normal operating

3 25 all LED’s are constant flashing

link is blinking

ready + line1/2 + door + aux + 100M (if link)

permanent for ca. 5s

link blinking

ready + 100M (if link)

link blinking

IP400

(all LED’s)

Button PPP+Tel.1+Tel.2: <5s blink, [5;8] constant flash, >8 ready + link + act constant flash

without ethernet cable plugged in: <8s off, 8s one blink, >8s off

3 25 ready + link + act flashing constant <8 ready + PPP + tel1 + tel2 constant flash,

[3;10] link + act. uncoordinated flashing

>10s ready + link (if link) constant act. blinking

ready + 100M (if link)

link blinking

IP3000

(all LED’s)

Button <6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,

act + speed + link off

>10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off

with ethernet cable plugged in: act + speed + link normal working state

fast blink (green) 3 25 all LED’s flashing permanent

ready off

link blinking

>2 link + speed constant flashing, act blinking

<5s PRI1 + PRI2 + S/T constant flash

>5s ready constant flash, (if link) link + speed constant flashing, act blinking

ready constant flash, (if link) link + speed constant flashing, act blinking blinking (green)
IP800/IP6000/IPx010

(red/green/orange ready LED )

Button <6 slow gn blink

[6;10] constant red

[10;13] fast gn blink

<13 constant orange

fast blink (green) 3 15 (IP800)

15-20 (IP6000/IPx010)

constant orange red green blinking (red)
IP1200 Button <2s alarm red constant flash, ready off

[2;7] alarm off, ready slow blink green

[7;13] alarm off, ready fast blink green

>13s alarm off, ready 2 Hz blink green

fast blink 3 10 slow flash ca. 2 Hz <2s alarm red constant flash

ready green constant flash

power orange constant flash

[2;4] alarm off, ready off, power orange

>4s alarm off, ready constant green flash, power constant green flash

ready constant green flash and power constant orange flash alarm (red)
IP1202 Button <3s LED off

[3;10] LED blink fast blue 1 sec

>10s LED blink fast blue 1 sec, than blink slow blue until factory reset completed, than constant yellow/amber

fast blink in blue 3 10 constant yellow/amber LED red until firmware lstarted

LED blink fast red until ethernet link up

LED blink fast blue until Air Sync established

LED constant blue if Air Sync OK

LED constant blue LED constant red
IP200/IP202

(red handset)

alt key slow blink slow blink 3 5 constant flash slow blink off constant flash
IP200A/IP210

(red handset)

alt key slow blink fast blink 3 15 slow flash

ca. 2 Hz

on off blinking
IP110

(LED’s in F1 key)

save key slow blink F1 off 3 10 - 15 slow flash

ca. 2 Hz

constant F1 flash off blinking
IP101

(MWI LED)

backspace key press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink
IP102

(MWI LED)

backspace key press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink
IP111

(MWI LED)

home key press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink
IP112

(MWI LED)

home key press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink
IP230

(menu key)

menu key slow blink fast blink 3 10 slow flash

ca. 2 Hz

on off blinking
IP240

(menu key)

menu key slow blink fast blink 3 10 slow flash

ca. 2 Hz

on off blinking
IP241

(menu key)

alt key slow blink fast blink 3 10 slow flash

ca. 2 Hz

on off blinking
IP222

(MWI LED)

ESC key slow blink fast blink 3 15 slow flash

ca. 2 Hz

on off blinking
IP232

(MWI LED)

ESC key slow blink fast blink 3 15 slow flash

ca. 2 Hz

on off blinking

Related Articles

Personal tools