Reference7:Administration/PBX/General

From innovaphone wiki
Jump to navigation Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.
There are also other versions of this article available: Reference | Reference7 (this version) | Reference8 | Reference9 | Reference10 | Reference11r1 | Reference11r2 | Reference12r1 | Reference13r1 | Reference13r3 | Reference14r1

The fundamental operating modes of the PBX are configured on this page. These parameters are stored in the config file. All other PBX config is stored in the LDAP.

Configuration

Common

PBX Mode The PBX operating mode
  • Off - The PBX is disabled. After enabling the PBX a browser refresh is needed to activate additional PBX webpages.
  • Master - The PBX on this device acts as Master. Within a multisite installation exactly one PBX must be configured as Master.
  • Standby - The PBX on this device acts as Standby for the Master. As long as the master is available, this PBX is not active, but just monitors the Master. If the Master is not availabe this PBX is active.
  • Standby-Slave - The PBX on this device acts as Standby for a Slave. As long as the slave is available, this PBX is not active, but just monitors the slave. If the slave is not availabe this PBX is active.
System Name The system Name. On all PBX within a multisite installation the same System Name must be configured. For H.323 endpoints this name is the gatekeeper identifier, for SIP endpoints it is the server name.
PBX Name The name of the PBX on this device. With this name a PBX is associated to a node. The field 'Name' (not Long Name) of a PBX Node object relates to this name.
Unknown Registrations If this checkmark is set, the PBX accepts 'unknown' registrations. This means registrations with no matching object configured. If from an endpoint registered in this way a number of an object is dialed, which has no registration active and no 'HW-ID' configured the name used for the registration is configured as 'HW-ID' of this object. This is an easy way to deploy large numbers of phones.
Music On Hold URL A URL for the Music On Hold. This file is read by the PBX using HTTP and sent to a held endpoint via RTP. The format of this URL is

http://<addr>/<file>.$coder?coder=g729,g711a,g711u,g723&repeat=true. <addr> is the IP address of the http server, no dns name is allowed here. <file> is the filename. $coder will be replaced by the actual coder used. Parameters: coder=g729,g711a,g711u,g723 is the list of available coders. Only these coders must be specified for which a corresponding file exists. repeat=true should be specified in order to loop the file endlessly. random=true can be used to start the music on hold on a random point (this will work only if the URL is not local though).

By default the built-in Music-On-Hold is played (Pseudo URL: "MOH?coder=g729,g711a,g723&repeat=true"). You can also play a dial tone (Pseudo URL "TONE") or a ring-back tone (Pseudo URL "TONE?tone=ringback").If you configure a wrong (or invalid) URL then you will have silence as MOH.

External Music On Hold To offload the device from playing the Music on hold, the Music On Hold can be played by a seperate device. This device can register with a name configured here. To retrieve the Music On Hold a call is sent to this device. For each held endpoint a call is sent.
Response Timeout Global timeout (in seconds) after which any action for no response is taken (e.g. Call Forward on No Response). A timeout configured at any object overrides this value.
Dial Complete Timeout Global timeout (in seconds) after which any action for incomplete dialed number is taken (e.g. incomplete destination at trunk object).
No. of Regs w/o Pwd Number of registration without password authentication which are allowed per user. If 0 is configured no registration without password is possible.
Recall Timer A value configured here enables recall after transfer. If a call is transfered and not answered within this time, the call is sent back to the transfering endpoint.
Pickup Prefix V7 In V7, the pickup prefix is obsolete. Please use the pbx object DTMF Featurecodes.
Enable External Transfer Unless this checkbox is set any attempt to transfer an external call back to an external destination will result in disconnection of the call.
RTP Proxy (v6 SR2) If this checkbox is set, all media traffic is routed thru the PBX. Check this only if you need to have this, since it creates CPU load on the PBX.
Generate CDRs If this checkbox is set, the PBX generates CDRs for all calls. See Reference7:Call_Detail_Record_CDR_PBX for a description of the CDRs.
Route Root-Node External Calls to Destination object (Long Name) of Root-Node external calls. This configuration option is available on the Master or Standby PBX only. Any call call which cannot be terminated inside the PBX is sent to this destination as long as neither the source nor the destination of the call can be associated with a node with a PBX configured. This object must be assigned to this PBX.
Route PBX-Node External Calls to Destination object (Long Name) of PBX-Node external calls. Any call call which cannot be terminated inside the PBX is sent to this destination as long as the source or the destination of the call can be associated with the node of this PBX. If a call is sent from or to an object defined inside the node of this PBX or in a node hierachically below the node of this PBX the call is associated to the node of this PBX. This object must be assigned to this PBX, that is, it has to register to this PBX.
Escape Dialtone from The PBX object (Long Name) to which a call is made to get a dialtone if a dialtone is configured for the escape of a node. As above, this object must be assigned to this PBX.

Slave PBX

If the PBX is operated in Slave mode, then the Slave PBX section is displayed

Master The IP address of the PBX master
Alternate Master The IP address of an alternative PBX master (standby, if available
Password The password to be used for registration at the Master as configured in the Node Object
Route Master calls if no Master to If the master is not available, master calls are sent to this destination
Max Calls to Master This parameter can be used to limit the calls to the master. If a call is sent to the master and there are already calls to/from the master equal to or exceeding this value, the call is handled as if the master was not available.

Standby PBX

If the PBX is operated in Standby mode, then the Standby PBX section is displayed

Master The IP address of the PBX master

License Status

Licenses

A list of all installed PBX license with their current usage is displayed here.

Count The total number of installed licenses of this type.
Usage The total usage of this license type
Local The usage of this license on this PBX
Slaves The usage of this license on PBX's registered to this PBX.

see Reference7:Licenses for a description of the licenses.

Registrations

The current number of registrations and the limit as defined by the base license is displayed here. Because this limit is defined by the base license it includes any registrations because of standby as well, which require no registration license.