https://wiki.innovaphone.com/api.php?action=feedcontributions&feedformat=atom&user=Inno-kh 2026-04-23T18:45:54Z User contributions MediaWiki 1.42.3 https://wiki.innovaphone.com/index.php?title=Howto:Howto_use_the_Auerswald_FXO_Adapter_with_innovaphone&diff=11950 2008-10-01T09:16:47Z

<p>Inno-kh: </p> <hr /> <div>A analog PBX can’t be connected to an IP21 without any additional hardware.<br /> <br /> The use of a Auerswald FXO Adapter makes it possible to connect a analog PBX to the IP PBX<br /> <br /> ==Note==<br /> The AUERSWALD Box is out of stock (and - works only in one direction)<br /> Other product:<br /> see:<br /> http://wiki.innovaphone.com/index.php?title=Howto:Analog_Trunk_(FXO)_with_Linksys_SPA3102 <br /> <br /> <br /> <br /> ==Applies To==<br /> This information applies to<br /> <br /> * IP 21, V5.01<br /> Build 05-5880 and later.<br /> <br /> &lt;!-- Keywords: enter keywords, foreign translations and/or synoyms not appearing in the article here for better search results --&gt;<br /> <br /> ==More Information==<br /> <br /> ===Problem Details===<br /> The innovaphone IP21 only has a FXS Interface and can’t be connected to an anlog PBX (because it is also a FXS Interface). <br /> <br /> An adapter is needed to convert between both FXS Ports. Therefore the Auerswald Box can be used. <br /> <br /> Equipped with two FXO Interfaces it is possible to connect two FXS Interfaces together.<br /> <br /> ===System Requirements===<br /> The IP21 needs a firmware of 05-5880 or later<br /> ===Installation===<br /> <br /> [[image:Howto_use_the_Auerswald_FXO_Adapter_with_innovaphone_Auerswald1.PNG]]<br /> <br /> ===Configuration===<br /> Connect the devices as shown in Installation.<br /> <br /> If you now call to the Auerswald Adapter from the Analog PBX, a connection between the Analog PBX and the Auerswald Adapter is established. <br /> <br /> Now dialing is only possible with DTMF Tones. <br /> <br /> Each DTMF number will be dialed from the Auerswald Box. <br /> <br /> Therefore dial like normal and wait until the IP21 connects to the called party.<br /> <br /> For a more comfortable use for calls from the IP21 to the analog PBX you can add a special character in the routing table of the IP21.<br /> <br /> Special character: “^”<br /> <br /> All numbers after this character are dialed as DTMF Tones and you don’t need to dial after the first connection to the Auerswald Box.<br /> <br /> Example: <br /> <br /> called number in: “empty”<br /> called number out: ^1234<br /> <br /> Now every call executes the mapping dials “1234” as DTMF Tones and the Auerswald Box starts Dialing. <br /> <br /> The advantage is that no DTMF dialing is needed because the IP21 can do that now. <br /> <br /> Only the dialing to the Auerswald Box has to be done.<br /> <br /> <br /> &lt;!-- == Related Articles == --&gt;<br /> <br /> [[Category:Howto|{{PAGENAME}}]]</div>

Inno-kh https://wiki.innovaphone.com/index.php?title=Howto:V6_and_V7_on_IP21,_IP200_(old),_IP202_and_IP400&diff=11949 2008-10-01T08:44:48Z

<p>Inno-kh: </p> <hr /> <div>Due to flash and dram memory limitations, full the V6 feature set is not available on some older innovaphone platforms. You should generally consider replacing IP400 by IP305, as well as IP202 by a combination of IP110/IP200 and IP302.<br /> <br /> ==Applies To==<br /> This information applies to<br /> <br /> * IP400<br /> * IP21<br /> * IP200 (the old one, not IP200A, see label on the back)<br /> * IP202<br /> <br /> <br /> ==More Information==<br /> === Running V6 up to and including V6 SR1 ===<br /> On all IP400, all IP21 and IP202 with 8 MB Ram and 2MB Flash (see the info screen for details on how much memory your IP202 features), the V6 PBX will not run. The IP400 and IP21 firmware thus does not include the PBX at all.<br /> For the IP202, there are 2 downloads available, '''ip202.bin''' which includes the PBX and '''ip202phone.bin''' which does not. '''ip202.bin''' will not work on older IP202 platforms with only 2MB flash memory.<br /> <br /> The V6 Gateway/Gatekeeper - aka “Relay” - will still work on IP400 and IP21, but not on the smaller IP202 (in fact, the '''ip202phone.bin''' is identical to the '''ip200.bin''').<br /> <br /> You can check the size of flash/dram at the webinterface of your unit (General -&gt; Info). A line like '''Version V5.01 sr1-hotfix IP202[05-5874], Bootcode[336], HW[224] ''4096''/''8192''''' indicates 4MB flash and 8MB dram.<br /> <br /> &lt;center&gt;<br /> {| border=1<br /> |+V6 PBX compatibility for old devices <br /> !width=160|<br /> !width=150|V5 Gateway and PBX<br /> !width=100|V6 Gateway<br /> !width=100|V6 PBX<br /> |----<br /> |IP21<br /> |Yes<br /> |Yes<br /> |No<br /> |----<br /> |IP400<br /> |Yes<br /> |Yes<br /> |No<br /> |----<br /> |IP202 with 2MB Flash<br /> |Yes<br /> |No<br /> |No<br /> |----<br /> |IP202 with 4MB Flash<br /> |Yes<br /> |Yes<br /> |Yes <br /> |}<br /> &lt;/center&gt;<br /> <br /> === Running V6 SR2 ===<br /> From V6 SR2, there are addtional limitations.<br /> <br /> The IP200 (not IP200A) and IP202 with 2 MB Flash will include neither PPP nor NAT (this means no PPTP and PPPoE either). The phone can thus not be used as a router anymore.<br /> <br /> The IP400 does not include PPP (and thus no PPTP or PPPoE either), NAT, Telnet, Update, Aping, TCP-SIP und - as before - the PBX.<br /> <br /> === Running V6 SR2 HF8===<br /> From V6 SR2 HF8, there are addtional limitations.<br /> IP21 - need factory reset before upload - (flash memory to small)<br /> <br /> <br /> [[Category:Faq|{{PAGENAME}}]]</div>

Inno-kh