innovaphone wiki - User contributions [en]

File:SIP-Trunk - LCR Telecom - SIP Provider Compatibility Test 2.png

2015-03-31T07:36:28Z

Kdelporte:

File:SIP-Trunk - LCR Telecom - SIP Provider Compatibility Test 3.png

2015-03-31T07:15:35Z

Kdelporte:

File:SIP-Trunk - LCR Telecom - SIP Provider Compatibility Test.png

2015-03-31T07:13:00Z

Kdelporte:

File:SIP-Trunk - LCR Telecom - SIP Provider Compatibility Test 1.png

2015-03-31T07:08:26Z

Kdelporte:

Howto:SIP-Trunk - LCR Telecom - SIP Provider

2015-03-30T08:38:04Z

Kdelporte: /* Test Results */

[[Image:3rdPartyGoldfischglas 03.png|right]]
'''Innovaphone Compatibility Test Report'''

== Summary ==

'''SIP Provider: LCR Telecom'''

The provider supports all required innovaphone features and is therefore qualified as [[Howto:What_is_a_%22recommended_product%22%3F#SIP_Provider|recommended SIP Provider]].

...

That being said, the provider has achieved x% of all possible test points. For more information on the test rating, please refer to [[Howto:SIP_Interop_Test_Description#|Test Description]]




* Features:

** Direct Dial In
** Fax over IP (T.38)
** DTMF
** CGPN can be suppressed
** CLIP No Screening
** Reverse Media
** Transfer

* Supported Codecs by the provider
** G711
** G729
** G723
** T.38 UDP

== Current test state ==


{{Template:Compat Status "in progress"}}









<internal>
Beim Abschluss des Tests (egal ob gut, schlecht oder abgebrochen) bitte Nachricht an ckl!
</internal>

== Testing Enviroment ==

[[Image:SIPProviderTestTopology1.PNG]]

This scenario describes a setup where the PBX and phones are in a private network.

There are 3 major configuration variants of the SIP trunk, which one is used depends on the test results. The variants are:

* the SIP trunk is configured without Media Relay and without exclusive coder. This is the case if all tests were successful
* the SIP trunk is configured with Media Relay and STUN but without exclusive coder. This is the case when the test for "NAT Traversal" fails
* the SIP trunk is configured with Media Relay and exclusive coder. This is the case when the test for "Reverse Media Negotiation" fails

The test scenario should describe which SIP trunk configuration is needed.

In this scenario, I didn't had the change to test with a Fax, as no fax is currently available. As described in the test, it is possible to ask this as well at the Provider. He assured me that T38 protocol and the Transcoding of this protocol are not a problem.

== Test Results ==

For more information on the test procedure, please read the following wiki article: [[Howto:SIP_Interop_Test_Description|SIP Interop Test Description]]. Bold lines in the test results indicate a KO-criteria.

{{FIXME|reason=Note: Possible test results are Ok, Nok, Not tested, N/A(not available). Ok, Nok, N/A are self explanatory. "Not tested" is more a temporary note - if its still in the test after finishing, then the summary should explain why the feature was not tested. Remove this note in the final report}}

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|'''call using g711a'''
|OK
|----
|'''call using g711u'''
|OK
|----
|call using g723
|OK
|----
|call using g729
|OK
|----
|call using g722
|OK
|----
|Overlapped sending
|OK
|----
|'''early media channel'''
|OK
|----
|Fax using T.38
|OK
|----
|T.38 Transcoding by the provider
|OK
|----
|Reverse Media Negotiation
|OK
|----
|CGPN can be suppressed
|OK
|----
|CLIP no screening
|OK
|----
|'''Long time call possible(>30 min)'''
|OK
|----
|'''External Transfer'''
|OK
|----
|NAT Detection
|OK
|----
|Redundancy
|OK
|----
|SIP over TCP
|OK
|----
|'''Voice Quality OK?'''
|OK
|}

=== Direct Dial In ===

{| border="1"
!Tested feature
!Result
|----
|'''Inbound(Provider -> Innovaphone)'''
|OK
|----
|'''Outbound(Innovaphone -> Provider)'''
|OK
|----
|'''Loop In call(Innovaphone -> Provider -> Innovaphone)'''
|OK
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|'''DTMF tones sent correctly via RTP-events(RFC 2833)'''
|OK
|----
|DTMF tones sent correctly via SIP-Info
|OK
|----
|'''DTMF tones received correctly via RTP-events(RFC 2833)'''
|OK
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be put on hold'''
|OK
|----
|Held end hears music on hold / announcement from PBX
|OK
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold or dialling tone
|OK
|----
|'''Call returns to transferring device if the third'''
'''Endpoint is not available'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Call can be transferred
|OK
|----
|Held end hears dialling tone
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== CFU / CFB Transfer ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

=== CFNR / Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred or forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|'''Caller can make a call to a Broadcast Group'''
|OK
|----
|'''Caller can make a call to a Waiting Queue'''
|OK
|----
|'''Announcement if nobody picks up the call'''
|OK
|}

== Configuration ==

===Firmware version===

All innovaphone devices use V11SR1.

=== SIP - Trunk ===

=== Number Mapping ===

=== Route Settings ===

=== Media Relay ===

=== Fax ===

[[Category:Compat|{{PAGENAME}}]]

Howto:SIP-Trunk - LCR Telecom - SIP Provider

2015-03-30T08:37:22Z

Kdelporte: /* Testing Enviroment */

[[Image:3rdPartyGoldfischglas 03.png|right]]
'''Innovaphone Compatibility Test Report'''

== Summary ==

'''SIP Provider: LCR Telecom'''

The provider supports all required innovaphone features and is therefore qualified as [[Howto:What_is_a_%22recommended_product%22%3F#SIP_Provider|recommended SIP Provider]].

...

That being said, the provider has achieved x% of all possible test points. For more information on the test rating, please refer to [[Howto:SIP_Interop_Test_Description#|Test Description]]




* Features:

** Direct Dial In
** Fax over IP (T.38)
** DTMF
** CGPN can be suppressed
** CLIP No Screening
** Reverse Media
** Transfer

* Supported Codecs by the provider
** G711
** G729
** G723
** T.38 UDP

== Current test state ==


{{Template:Compat Status "in progress"}}









<internal>
Beim Abschluss des Tests (egal ob gut, schlecht oder abgebrochen) bitte Nachricht an ckl!
</internal>

== Testing Enviroment ==

[[Image:SIPProviderTestTopology1.PNG]]

This scenario describes a setup where the PBX and phones are in a private network.

There are 3 major configuration variants of the SIP trunk, which one is used depends on the test results. The variants are:

* the SIP trunk is configured without Media Relay and without exclusive coder. This is the case if all tests were successful
* the SIP trunk is configured with Media Relay and STUN but without exclusive coder. This is the case when the test for "NAT Traversal" fails
* the SIP trunk is configured with Media Relay and exclusive coder. This is the case when the test for "Reverse Media Negotiation" fails

The test scenario should describe which SIP trunk configuration is needed.

In this scenario, I didn't had the change to test with a Fax, as no fax is currently available. As described in the test, it is possible to ask this as well at the Provider. He assured me that T38 protocol and the Transcoding of this protocol are not a problem.

== Test Results ==

For more information on the test procedure, please read the following wiki article: [[Howto:SIP_Interop_Test_Description|SIP Interop Test Description]]. Bold lines in the test results indicate a KO-criteria.

{{FIXME|reason=Note: Possible test results are Ok, Nok, Not tested, N/A(not available). Ok, Nok, N/A are self explanatory. "Not tested" is more a temporary note - if its still in the test after finishing, then the summary should explain why the feature was not tested. Remove this note in the final report}}

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|'''call using g711a'''
|OK
|----
|'''call using g711u'''
|OK
|----
|call using g723
|
|----
|call using g729
|OK
|----
|call using g722
|OK
|----
|Overlapped sending
|OK
|----
|'''early media channel'''
|OK
|----
|Fax using T.38
|
|----
|T.38 Transcoding by the provider
|
|----
|Reverse Media Negotiation
|OK
|----
|CGPN can be suppressed
|OK
|----
|CLIP no screening
|OK
|----
|'''Long time call possible(>30 min)'''
|OK
|----
|'''External Transfer'''
|OK
|----
|NAT Detection
|OK
|----
|Redundancy
|OK
|----
|SIP over TCP
|
|----
|'''Voice Quality OK?'''
|OK
|}

=== Direct Dial In ===

{| border="1"
!Tested feature
!Result
|----
|'''Inbound(Provider -> Innovaphone)'''
|OK
|----
|'''Outbound(Innovaphone -> Provider)'''
|OK
|----
|'''Loop In call(Innovaphone -> Provider -> Innovaphone)'''
|OK
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|'''DTMF tones sent correctly via RTP-events(RFC 2833)'''
|OK
|----
|DTMF tones sent correctly via SIP-Info
|OK
|----
|'''DTMF tones received correctly via RTP-events(RFC 2833)'''
|OK
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be put on hold'''
|OK
|----
|Held end hears music on hold / announcement from PBX
|OK
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold or dialling tone
|OK
|----
|'''Call returns to transferring device if the third'''
'''Endpoint is not available'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Call can be transferred
|OK
|----
|Held end hears dialling tone
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== CFU / CFB Transfer ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

=== CFNR / Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred or forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|'''Caller can make a call to a Broadcast Group'''
|OK
|----
|'''Caller can make a call to a Waiting Queue'''
|OK
|----
|'''Announcement if nobody picks up the call'''
|OK
|}

== Configuration ==

===Firmware version===

All innovaphone devices use V11SR1.

=== SIP - Trunk ===

=== Number Mapping ===

=== Route Settings ===

=== Media Relay ===

=== Fax ===

[[Category:Compat|{{PAGENAME}}]]

Howto:SIP-Trunk - LCR Telecom - SIP Provider

2015-03-30T08:37:08Z

Kdelporte: /* Testing Enviroment */

[[Image:3rdPartyGoldfischglas 03.png|right]]
'''Innovaphone Compatibility Test Report'''

== Summary ==

'''SIP Provider: LCR Telecom'''

The provider supports all required innovaphone features and is therefore qualified as [[Howto:What_is_a_%22recommended_product%22%3F#SIP_Provider|recommended SIP Provider]].

...

That being said, the provider has achieved x% of all possible test points. For more information on the test rating, please refer to [[Howto:SIP_Interop_Test_Description#|Test Description]]




* Features:

** Direct Dial In
** Fax over IP (T.38)
** DTMF
** CGPN can be suppressed
** CLIP No Screening
** Reverse Media
** Transfer

* Supported Codecs by the provider
** G711
** G729
** G723
** T.38 UDP

== Current test state ==


{{Template:Compat Status "in progress"}}









<internal>
Beim Abschluss des Tests (egal ob gut, schlecht oder abgebrochen) bitte Nachricht an ckl!
</internal>

== Testing Enviroment ==

[[Image:SIPProviderTestTopology1.PNG]]

This scenario describes a setup where the PBX and phones are in a private network.

There are 3 major configuration variants of the SIP trunk, which one is used depends on the test results. The variants are:

* the SIP trunk is configured without Media Relay and without exclusive coder. This is the case if all tests were successful
* the SIP trunk is configured with Media Relay and STUN but without exclusive coder. This is the case when the test for "NAT Traversal" fails
* the SIP trunk is configured with Media Relay and exclusive coder. This is the case when the test for "Reverse Media Negotiation" fails

The test scenario should describe which SIP trunk configuration is needed.

In this scenario, I didnt had the change to test with a Fax, as no fax is currently available. As described in the test, it is possible to ask this as well at the Provider. He assured me that T38 protocol and the Transcoding of this protocol are not a problem.

== Test Results ==

For more information on the test procedure, please read the following wiki article: [[Howto:SIP_Interop_Test_Description|SIP Interop Test Description]]. Bold lines in the test results indicate a KO-criteria.

{{FIXME|reason=Note: Possible test results are Ok, Nok, Not tested, N/A(not available). Ok, Nok, N/A are self explanatory. "Not tested" is more a temporary note - if its still in the test after finishing, then the summary should explain why the feature was not tested. Remove this note in the final report}}

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|'''call using g711a'''
|OK
|----
|'''call using g711u'''
|OK
|----
|call using g723
|
|----
|call using g729
|OK
|----
|call using g722
|OK
|----
|Overlapped sending
|OK
|----
|'''early media channel'''
|OK
|----
|Fax using T.38
|
|----
|T.38 Transcoding by the provider
|
|----
|Reverse Media Negotiation
|OK
|----
|CGPN can be suppressed
|OK
|----
|CLIP no screening
|OK
|----
|'''Long time call possible(>30 min)'''
|OK
|----
|'''External Transfer'''
|OK
|----
|NAT Detection
|OK
|----
|Redundancy
|OK
|----
|SIP over TCP
|
|----
|'''Voice Quality OK?'''
|OK
|}

=== Direct Dial In ===

{| border="1"
!Tested feature
!Result
|----
|'''Inbound(Provider -> Innovaphone)'''
|OK
|----
|'''Outbound(Innovaphone -> Provider)'''
|OK
|----
|'''Loop In call(Innovaphone -> Provider -> Innovaphone)'''
|OK
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|'''DTMF tones sent correctly via RTP-events(RFC 2833)'''
|OK
|----
|DTMF tones sent correctly via SIP-Info
|OK
|----
|'''DTMF tones received correctly via RTP-events(RFC 2833)'''
|OK
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be put on hold'''
|OK
|----
|Held end hears music on hold / announcement from PBX
|OK
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold or dialling tone
|OK
|----
|'''Call returns to transferring device if the third'''
'''Endpoint is not available'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Call can be transferred
|OK
|----
|Held end hears dialling tone
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== CFU / CFB Transfer ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

=== CFNR / Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred or forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|'''Caller can make a call to a Broadcast Group'''
|OK
|----
|'''Caller can make a call to a Waiting Queue'''
|OK
|----
|'''Announcement if nobody picks up the call'''
|OK
|}

== Configuration ==

===Firmware version===

All innovaphone devices use V11SR1.

=== SIP - Trunk ===

=== Number Mapping ===

=== Route Settings ===

=== Media Relay ===

=== Fax ===

[[Category:Compat|{{PAGENAME}}]]

Howto:SIP-Trunk - LCR Telecom - SIP Provider

2015-03-30T08:33:50Z

Kdelporte: /* Summary */

[[Image:3rdPartyGoldfischglas 03.png|right]]
'''Innovaphone Compatibility Test Report'''

== Summary ==

'''SIP Provider: LCR Telecom'''

The provider supports all required innovaphone features and is therefore qualified as [[Howto:What_is_a_%22recommended_product%22%3F#SIP_Provider|recommended SIP Provider]].

...

That being said, the provider has achieved x% of all possible test points. For more information on the test rating, please refer to [[Howto:SIP_Interop_Test_Description#|Test Description]]




* Features:

** Direct Dial In
** Fax over IP (T.38)
** DTMF
** CGPN can be suppressed
** CLIP No Screening
** Reverse Media
** Transfer

* Supported Codecs by the provider
** G711
** G729
** G723
** T.38 UDP

== Current test state ==


{{Template:Compat Status "in progress"}}









<internal>
Beim Abschluss des Tests (egal ob gut, schlecht oder abgebrochen) bitte Nachricht an ckl!
</internal>

== Testing Enviroment ==

[[Image:SIPProviderTestTopology1.PNG]]

This scenario describes a setup where the PBX and phones are in a private network.

There are 3 major configuration variants of the SIP trunk, which one is used depends on the test results. The variants are:

* the SIP trunk is configured without Media Relay and without exclusive coder. This is the case if all tests were successful
* the SIP trunk is configured with Media Relay and STUN but without exclusive coder. This is the case when the test for "NAT Traversal" fails
* the SIP trunk is configured with Media Relay and exclusive coder. This is the case when the test for "Reverse Media Negotiation" fails

The test scenario should describe which SIP trunk configuration is needed.

== Test Results ==

For more information on the test procedure, please read the following wiki article: [[Howto:SIP_Interop_Test_Description|SIP Interop Test Description]]. Bold lines in the test results indicate a KO-criteria.

{{FIXME|reason=Note: Possible test results are Ok, Nok, Not tested, N/A(not available). Ok, Nok, N/A are self explanatory. "Not tested" is more a temporary note - if its still in the test after finishing, then the summary should explain why the feature was not tested. Remove this note in the final report}}

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|'''call using g711a'''
|OK
|----
|'''call using g711u'''
|OK
|----
|call using g723
|
|----
|call using g729
|OK
|----
|call using g722
|OK
|----
|Overlapped sending
|OK
|----
|'''early media channel'''
|OK
|----
|Fax using T.38
|
|----
|T.38 Transcoding by the provider
|
|----
|Reverse Media Negotiation
|OK
|----
|CGPN can be suppressed
|OK
|----
|CLIP no screening
|OK
|----
|'''Long time call possible(>30 min)'''
|OK
|----
|'''External Transfer'''
|OK
|----
|NAT Detection
|OK
|----
|Redundancy
|OK
|----
|SIP over TCP
|
|----
|'''Voice Quality OK?'''
|OK
|}

=== Direct Dial In ===

{| border="1"
!Tested feature
!Result
|----
|'''Inbound(Provider -> Innovaphone)'''
|OK
|----
|'''Outbound(Innovaphone -> Provider)'''
|OK
|----
|'''Loop In call(Innovaphone -> Provider -> Innovaphone)'''
|OK
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|'''DTMF tones sent correctly via RTP-events(RFC 2833)'''
|OK
|----
|DTMF tones sent correctly via SIP-Info
|OK
|----
|'''DTMF tones received correctly via RTP-events(RFC 2833)'''
|OK
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be put on hold'''
|OK
|----
|Held end hears music on hold / announcement from PBX
|OK
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold or dialling tone
|OK
|----
|'''Call returns to transferring device if the third'''
'''Endpoint is not available'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Call can be transferred
|OK
|----
|Held end hears dialling tone
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== CFU / CFB Transfer ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

=== CFNR / Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred or forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|'''Caller can make a call to a Broadcast Group'''
|OK
|----
|'''Caller can make a call to a Waiting Queue'''
|OK
|----
|'''Announcement if nobody picks up the call'''
|OK
|}

== Configuration ==

===Firmware version===

All innovaphone devices use V11SR1.

=== SIP - Trunk ===

=== Number Mapping ===

=== Route Settings ===

=== Media Relay ===

=== Fax ===

[[Category:Compat|{{PAGENAME}}]]

Howto:SIP-Trunk - LCR Telecom - SIP Provider

2015-03-24T13:31:09Z

Kdelporte:

[[Image:3rdPartyGoldfischglas 03.png|right]]
'''Innovaphone Compatibility Test Report'''

== Summary ==

'''SIP Provider: LCR Telecom'''

The provider supports all required innovaphone features and is therefore qualified as [[Howto:What_is_a_%22recommended_product%22%3F#SIP_Provider|recommended SIP Provider]].

...

That being said, the provider has achieved x% of all possible test points. For more information on the test rating, please refer to [[Howto:SIP_Interop_Test_Description#|Test Description]]




* Features:

** Direct Dial In
** Fax over IP (T.38)
** DTMF

* Supported Codecs by the provider
** G711
** G729
** G723
** G726
** T.38 UDP

== Current test state ==


{{Template:Compat Status "in progress"}}









<internal>
Beim Abschluss des Tests (egal ob gut, schlecht oder abgebrochen) bitte Nachricht an ckl!
</internal>

== Testing Enviroment ==

[[Image:SIPProviderTestTopology1.PNG]]

This scenario describes a setup where the PBX and phones are in a private network.

There are 3 major configuration variants of the SIP trunk, which one is used depends on the test results. The variants are:

* the SIP trunk is configured without Media Relay and without exclusive coder. This is the case if all tests were successful
* the SIP trunk is configured with Media Relay and STUN but without exclusive coder. This is the case when the test for "NAT Traversal" fails
* the SIP trunk is configured with Media Relay and exclusive coder. This is the case when the test for "Reverse Media Negotiation" fails

The test scenario should describe which SIP trunk configuration is needed.

== Test Results ==

For more information on the test procedure, please read the following wiki article: [[Howto:SIP_Interop_Test_Description|SIP Interop Test Description]]. Bold lines in the test results indicate a KO-criteria.

{{FIXME|reason=Note: Possible test results are Ok, Nok, Not tested, N/A(not available). Ok, Nok, N/A are self explanatory. "Not tested" is more a temporary note - if its still in the test after finishing, then the summary should explain why the feature was not tested. Remove this note in the final report}}

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|'''call using g711a'''
|OK
|----
|'''call using g711u'''
|OK
|----
|call using g723
|
|----
|call using g729
|OK
|----
|call using g722
|OK
|----
|Overlapped sending
|OK
|----
|'''early media channel'''
|OK
|----
|Fax using T.38
|
|----
|T.38 Transcoding by the provider
|
|----
|Reverse Media Negotiation
|OK
|----
|CGPN can be suppressed
|OK
|----
|CLIP no screening
|OK
|----
|'''Long time call possible(>30 min)'''
|OK
|----
|'''External Transfer'''
|OK
|----
|NAT Detection
|OK
|----
|Redundancy
|OK
|----
|SIP over TCP
|
|----
|'''Voice Quality OK?'''
|OK
|}

=== Direct Dial In ===

{| border="1"
!Tested feature
!Result
|----
|'''Inbound(Provider -> Innovaphone)'''
|OK
|----
|'''Outbound(Innovaphone -> Provider)'''
|OK
|----
|'''Loop In call(Innovaphone -> Provider -> Innovaphone)'''
|OK
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|'''DTMF tones sent correctly via RTP-events(RFC 2833)'''
|OK
|----
|DTMF tones sent correctly via SIP-Info
|OK
|----
|'''DTMF tones received correctly via RTP-events(RFC 2833)'''
|OK
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be put on hold'''
|OK
|----
|Held end hears music on hold / announcement from PBX
|OK
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|OK
|----
|Held end hears music on hold or dialling tone
|OK
|----
|'''Call returns to transferring device if the third'''
'''Endpoint is not available'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|OK
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Call can be transferred
|OK
|----
|Held end hears dialling tone
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== CFU / CFB Transfer ===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

=== CFNR / Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred or forward'''
|OK
|----
|'''Held end hears dialling tone'''
|OK
|}

The following tests are made to test if call transfer is working.

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|OK
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|OK
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|OK
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|'''Caller can make a call to a Broadcast Group'''
|OK
|----
|'''Caller can make a call to a Waiting Queue'''
|OK
|----
|'''Announcement if nobody picks up the call'''
|OK
|}

== Configuration ==

===Firmware version===

All innovaphone devices use V11SR1.

=== SIP - Trunk ===

=== Number Mapping ===

=== Route Settings ===

=== Media Relay ===

=== Fax ===

[[Category:Compat|{{PAGENAME}}]]