innovaphone wiki - User contributions [en]

Howto:Guideline V5 to V6 upgrade

2007-11-26T14:11:56Z

Libby: /* Unnecessary routes */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please first read the upgrade issues article about licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 PBX only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location there is no local PBX to which the phones can also register to.

Because after the update to V6, the gatekeeper entry in the phones is lost - so the phones need to connect to the PBX via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/PBX (if you have a master slave configuration - update first the master PBX)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – Go to the Licence Manager.

Here the licences are not described in depth, this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the PBX to V6 you have to PAY for a basic licence – upgrading a V5 PBX to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences. If you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrading, input your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call. If unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure an own EXTERN user on every PBX (in the Numbering Node) and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (to have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. There is an innovaphone gateway with ISDN connection (local ISDN trunk) at every site (location)and more nodes over all locations. That means it is possible to have the same phone extensions over different nodes. Every endpoint only dials the extension inbetween its own node - if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and obtains a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls in the waiting queue as shown above

===Unnecessary routes===

Delete the routes to http interface and the user in the pbx for that route - you can delete all the routes and gws that you needed for the MOH in V5. It simplifies your configuration and saves Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:41:47Z

Libby: /* Locations Concept in V5 */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please first read the upgrade issues article about licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 PBX only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location there is no local PBX to which the phones can also register to.

Because after the update to V6, the gatekeeper entry in the phones is lost - so the phones need to connect to the PBX via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/PBX (if you have a master slave configuration - update first the master PBX)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – Go to the Licence Manager.

Here the licences are not described in depth, this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the PBX to V6 you have to PAY for a basic licence – upgrading a V5 PBX to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences. If you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrading, input your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call. If unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure an own EXTERN user on every PBX (in the Numbering Node) and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (to have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. There is an innovaphone gateway with ISDN connection (local ISDN trunk) at every site (location)and more nodes over all locations. That means it is possible to have the same phone extensions over different nodes. Every endpoint only dials the extension inbetween its own node - if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and obtains a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls in the waiting queue as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and gws that you needed for the MOH in V5. It simplifies your configuration and saves Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:41:26Z

Libby: /* Locations Concept in V5 */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please first read the upgrade issues article about licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 PBX only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location there is no local PBX to which the phones can also register to.

Because after the update to V6, the gatekeeper entry in the phones is lost - so the phones need to connect to the PBX via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/PBX (if you have a master slave configuration - update first the master PBX)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – Go to the Licence Manager.

Here the licences are not described in depth, this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the PBX to V6 you have to PAY for a basic licence – upgrading a V5 PBX to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences. If you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrading, input your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call. If unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure an own EXTERN user on every PBX (in the Numbering Node) and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (to have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. There is an innovaphone gateway with ISDN connection (local ISDN trunk) at every site (location)and more nodes over all locations. That means it is possible to have the same phone extensions over different nodes. Every endpoint only dials the extension inbetween its own node - if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls in the waiting queue as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and gws that you needed for the MOH in V5. It simplifies your configuration and saves Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:39:40Z

Libby: /* licences */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please first read the upgrade issues article about licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 PBX only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location there is no local PBX to which the phones can also register to.

Because after the update to V6, the gatekeeper entry in the phones is lost - so the phones need to connect to the PBX via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/PBX (if you have a master slave configuration - update first the master PBX)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – Go to the Licence Manager.

Here the licences are not described in depth, this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the PBX to V6 you have to PAY for a basic licence – upgrading a V5 PBX to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences. If you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrading, input your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call. If unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure an own EXTERN user on every PBX (in the Numbering Node) and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (to have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls in the waiting queue as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and gws that you needed for the MOH in V5. It simplifies your configuration and saves Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:38:49Z

Libby: /* Upgrade */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please first read the upgrade issues article about licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 PBX only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location there is no local PBX to which the phones can also register to.

Because after the update to V6, the gatekeeper entry in the phones is lost - so the phones need to connect to the PBX via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/PBX (if you have a master slave configuration - update first the master PBX)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – Go to the Licence Manager.

Here the licences are not described in depth, this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the PBX to V6 you have to PAY for a basic licence – upgrading a V5 PBX to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences. If you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put your licences in again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call. If unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure an own EXTERN user on every PBX (in the Numbering Node) and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (to have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls in the waiting queue as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and gws that you needed for the MOH in V5. It simplifies your configuration and saves Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:33:07Z

Libby: /* Configuration */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please first read the upgrade issues article about licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 PBX only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location there is no local PBX to which the phones can also register to.

Because after the update to V6, the gatekeeper entry in the phones is lost - so the phones need to connect to the PBX via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master PBX)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – Go to the Licence Manager.

Here the licences are not described in depth, this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the PBX to V6 you have to PAY for a basic licence – upgrading a V5 PBX to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences. If you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put your licences in again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call. If unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure an own EXTERN user on every PBX (in the Numbering Node) and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (to have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls in the waiting queue as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and gws that you needed for the MOH in V5. It simplifies your configuration and saves Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:24:11Z

Libby: /* Broadcast Group & Waiting Queue */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set a normal user in the PBX

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless LAN

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minute

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone PBX and innovaphone IP phones connected with H.323 to the PBX

Summary:

* The voice quality is good - hold/retrieve is working (from Nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the Nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Holding end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Holding end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Holding end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast & waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a broadcast group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:22:58Z

Libby: /* Hold/Retrieve */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set a normal user in the PBX

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless LAN

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minute

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone PBX and innovaphone IP phones connected with H.323 to the PBX

Summary:

* The voice quality is good - hold/retrieve is working (from Nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the Nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Holding end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Holding end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Holding end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast &waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a Broadcast Group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a Waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:22:24Z

Libby: /* Blind Transfer */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set a normal user in the PBX

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless LAN

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minute

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone PBX and innovaphone IP phones connected with H.323 to the PBX

Summary:

* The voice quality is good - hold/retrieve is working (from Nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the Nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Held end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Holding end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Holding end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast &waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a Broadcast Group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a Waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:22:12Z

Libby: /* Transfer with consultation */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set a normal user in the PBX

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless LAN

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minute

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone PBX and innovaphone IP phones connected with H.323 to the PBX

Summary:

* The voice quality is good - hold/retrieve is working (from Nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the Nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Held end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Holding end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast &waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a Broadcast Group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a Waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:21:38Z

Libby: /* Test Results */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set a normal user in the PBX

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless LAN

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minute

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone PBX and innovaphone IP phones connected with H.323 to the PBX

Summary:

* The voice quality is good - hold/retrieve is working (from Nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the Nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Held end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast &waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a Broadcast Group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a Waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:20:08Z

Libby: /* Internet tel settings */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set a normal user in the PBX

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless LAN

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minute

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone pbx and innovaphone IP Phones connected with H.323 to the pbx

Summary:

* The voice quality is good - hold/retrieve is working (from nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant Transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Held end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast &waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a Broadcast Group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a Waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:19:20Z

Libby: /* innovaphone configuration */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set a normal user in the PBX

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless lan

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minute

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone pbx and innovaphone IP Phones connected with H.323 to the pbx

Summary:

* The voice quality is good - hold/retrieve is working (from nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant Transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Held end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast &waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a Broadcast Group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a Waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:19:03Z

Libby: /* Nokia E65: */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set an normal user in the Pbx

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless lan

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minute

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone pbx and innovaphone IP Phones connected with H.323 to the pbx

Summary:

* The voice quality is good - hold/retrieve is working (from nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant Transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Held end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast &waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a Broadcast Group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a Waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Nokia Mobile Phones E Series

2007-11-15T20:18:24Z

Libby: /* Applies To */

'''Innovaphone Compatibility Test Report'''

This Article describes how to connect (and what is working) Nokia E Series Mobile phone (dual-mode phone ) with innovaphone Pbx.

Tested with the Nokia E65

===Applies To===

This information applies to

* all innovaphone PBX

Build V6 07-60711, and later

* Nokia E65

Software version: 1.0633.58.03

==innovaphone configuration==

set an normal user in the Pbx

for example

Long Name: E60

Name: E60

Number: 60

== Nokia E65: ==

Settings on Nokia E65

===Sip Settings===

Navigate to Tools->Settings->Connection->SIP settings:

Profile name: "innovaphone" (or anything else)

Service profile: IETF

Default access point: <your wifi access point>

Public user name: sip:E60@<IP address of your innovaphone pbx>

Use compression: No

Registration: Always on

Use security: No

===Proxy server===

tools -> settings -> connection -> SIP settings -> Proxy Server

Proxy server address: sip:<IP address of your innovaphone pbx>

Realm: <IP address of your IP800>

User name: E60

Password: <secret>

Allow loose routing: Yes

Transport type: UDP

Port: 5060

===Registrar server===

tools -> settings -> connection -> SIP settings -> Registrar Server

Registrar serv.addr.:<IP address of your innovaphone pbx>

Realm: <IP address of your innovaphone pbx>

User name: E60

Password: <secret>

Transport type: UDP

Port: 5060

===Internet tel settings===

tools -> settings -> connection -> Internet tel settings

give the name and profile

For trouble shooting purpose take the option of Wireless lan

tools -> settings -> connection -> Wireless LAN

Show availability Yes

Scan for Networks every minutes

== Supported Codecs ==

{| border="1"
!Codec
!Applies
|----
|G711
|yes
|----
|G729
|yes
|----
|G723
|not supported by nokia
|----
|G726
|not supported by nokia
|----
|GSM
|no
|----
|T.38 UDP
|no
|----
|G722
|not supported by nokia
|}

== Test Results ==

Tested with innovaphone pbx and innovaphone IP Phones connected with H.323 to the pbx

Summary:

* The voice quality is good - hold/retrieve is working (from nokia and from innovaphone phone).

* Transfer with consultation is working (but only when there is no codec change)

* semi attendant Transfer - or so called transfer without consultation is not working

* Blind transfer is working

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g723
|no
|----
|call using g729
|yes
|----
|Overlapped sending
|yes
|----
|early media channel
|not tested
|----
|Fax
|no
|----
|Voice Quality OK?
|yes
|}

=== Dial Inward ===

{| border="1"
!Tested feature
!Result
|----
|Inbound(nokia -> innovaphone Phone & via isdn)
|yes
|----
|Outbound(innovaphone Phone & via isdn -> nokia)
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result S1
|----
|DTMF tones sent correctly
|yes
|----
|DTMF tones received correctly (audible)
|no
|}

=== Hold/Retrieve ===

hold possible with the nokia phone and the innovaphone phone

{| border="1"
!Tested feature
!Result
|----
|Device can put call on hold
|yes
|----
|Held end hears music on hold
|no - instead one beep tone and information on display that call is on hold
|----
|Device can terminate either call and retrieve remaining call
|yes (nokia device and innovaphone IP Phone)
|}

=== Transfer with consultation===
Transfer only working when there is no codec change

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears music on hold
|no-instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Transfer with consultation (alerting only)===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|no
|----
|Held end hears music on hold or dialing tone
|no - instead one beep tone and information on display that call is on hold
|----
|Call returns to transferring device if the third
Endpoint is not available
|yes
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Result
|----
|Device can transfer call
|yes
|----
|Held end hears dialing tone
|no instead one beep tone and information on display that call is on hold
|}

=== Broadcast Group & Waiting Queue ===

tested also when the nokia phone is part of broadcast &waiting queue

{| border="1"
!Tested feature
!Result
|----
|Caller can make a call to a Broadcast Group
|yes (also when nokia phone is part of)
|----
|Caller can make a call to a Waiting Queue
|yes (also when nokia phone is part of)
|----
|Announcement if nobody picks up the call
|yes ( only with same codec)
|}

=== Calling Party Number ===

{| border="1"
!Tested feature
!Result
|----
|CGPN is displayed correctly
|yes
|----
|CGPN can be supressed
|via pbx - send number changes the cgpn
|}

==Additional Info==

To check your latest software version press *#0000# on your nokia phone and go to http://europe.nokia.com/A4577224

[[Category:Compat|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:17:46Z

Libby: /* Unnecessary routes */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – go to the Licence Manager.

Here the licences are not described in depth,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic licence – upgrading a V5 Pbx to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure on every PBX (in the Numbering Node) an own EXTERN user and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (that you have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls as shown abovein the waiting queue

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and gws that you needed for the MOH in V5. It simplifies your configuration and saves Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:15:23Z

Libby: /* Unnecessary routes */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – go to the Licence Manager.

Here the licences are not described in depth,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic licence – upgrading a V5 Pbx to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure on every PBX (in the Numbering Node) an own EXTERN user and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (that you have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls as shown abovein the waiting queue

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and gws that you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:13:09Z

Libby: /* Node */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – go to the Licence Manager.

Here the licences are not described in depth,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic licence – upgrading a V5 Pbx to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure on every PBX (in the Numbering Node) an own EXTERN user and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (that you have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls as shown abovein the waiting queue

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and Gw´s what you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location, all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:10:50Z

Libby: /* Waiting Queue */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – go to the Licence Manager.

Here the licences are not described in depth,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic licence – upgrading a V5 Pbx to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure on every PBX (in the Numbering Node) an own EXTERN user and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (that you have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also you need to change the urls as shown abovein the waiting queue

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and Gw´s what you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no Location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:10:29Z

Libby: /* MOH */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – go to the Licence Manager.

Here the licences are not described in depth,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic licence – upgrading a V5 Pbx to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure on every PBX (in the Numbering Node) an own EXTERN user and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (that you have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there also exists no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in PBX/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also in the waiting queue you need to change the urls as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and Gw´s what you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no Location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:08:58Z

Libby: /* Locations Concept in V5 */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – go to the Licence Manager.

Here the licences are not described in depth,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic licence – upgrading a V5 Pbx to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure on every PBX (in the Numbering Node) an own EXTERN user and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept is obsolete as it is in V5 - in V6 we call it Numbering Node

If you have more PBXs configured as Locations Concept in V5 - and every PBX has its own trunk local object (locally registered) - in V6 it works differently.

How to configure this in V6 (that you have an own Trunk Object with the same Number (e.g 0) on every site) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was impossible in v5 ):

Having more innovaphone locations. On every site (location) there is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension inbetween the own node- if it should reach another node, the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there exists also no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in Pbx/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also in the waiting queue you need to change the urls as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and Gw´s what you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no Location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:06:13Z

Libby: /* Extern Object */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – go to the Licence Manager.

Here the licences are not described in depth,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic licence – upgrading a V5 Pbx to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause, code send it to the extern object.

To configure on every PBX (in the Numbering Node) an own EXTERN user and set it also in the PBX /General at Route root node external calls to and/or route node external calls to.

The Extern Object can now be any object - but there is only one Extern for the whole root node.

Also you can define an own Extern Object for every Node.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept as it is in V5 is obsolete - in V6 we call it Numbering Node

If you have more Pbx´s configured as Locations Concept in V5 - and every Pbx has an own Trunk Local object (locally registered) - in V6 it works different.

How to configure this in V6 (that you have on every site an own Trunk Object with the same Number (e.g 0) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was in v5 impossible):

Having more innovaphone locations. On every site (location) is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension in-between the own node- if its to reach another node the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there exists also no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in Pbx/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also in the waiting queue you need to change the urls as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and Gw´s what you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no Location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:03:24Z

Libby: /* licences */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First take care of the licences when upgrading your PBX! – go to the Licence Manager.

Here the licences are not described in depth,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic licence – upgrading a V5 Pbx to V6 PBX is not for free!!!

The old V5 Trial Lics do not work with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade, put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause code send it to the extern object.

To configure on every Pbx (in the Numbering Node) a own EXTERN user and set it also in the Pbx /General at Route root node external calls to and/or route node external calls to.

The Extern Object can be now any Object - but there is only one Extern for the whole root node .

Alslo you can define for every Node an own Extern Obejct.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept as it is in V5 is obsolete - in V6 we call it Numbering Node

If you have more Pbx´s configured as Locations Concept in V5 - and every Pbx has an own Trunk Local object (locally registered) - in V6 it works different.

How to configure this in V6 (that you have on every site an own Trunk Object with the same Number (e.g 0) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was in v5 impossible):

Having more innovaphone locations. On every site (location) is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension in-between the own node- if its to reach another node the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there exists also no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in Pbx/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also in the waiting queue you need to change the urls as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and Gw´s what you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no Location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:01:45Z

Libby: /* Phone config */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First Take care of the Licences when upgrading your PBX! – go to the Licence Manager.

Here the Licences are not described in deep ,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic Licence – upgrading an V5 Pbx to V6 PBX is not for Free!!!

The old V5 Trial Lics are not working with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause code send it to the extern object.

To configure on every Pbx (in the Numbering Node) a own EXTERN user and set it also in the Pbx /General at Route root node external calls to and/or route node external calls to.

The Extern Object can be now any Object - but there is only one Extern for the whole root node .

Alslo you can define for every Node an own Extern Obejct.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept as it is in V5 is obsolete - in V6 we call it Numbering Node

If you have more Pbx´s configured as Locations Concept in V5 - and every Pbx has an own Trunk Local object (locally registered) - in V6 it works different.

How to configure this in V6 (that you have on every site an own Trunk Object with the same Number (e.g 0) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was in v5 impossible):

Having more innovaphone locations. On every site (location) is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension in-between the own node- if its to reach another node the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there exists also no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in Pbx/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also in the waiting queue you need to change the urls as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and Gw´s what you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no Location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Guideline V5 to V6 upgrade

2007-11-15T20:01:05Z

Libby: /* Phone Update */

This article describes the Guideline how to migrate from V5 to V6

==Applies to==

*all innovaphone devices V5

{{FIXME|reason=to be finished}}

==Configuration==

Please read first the Upgrade Issues article about the Licenses and other tweaks

[[Howto:Upgrade Issues V5 to V6]]

Then configure from v5 to v6 step by step as described below.

===Phone Update===

You first need to update all innovaphone phones to Version 6.

Therefore you send an update URL to the phones via the Version 5 PBX (PBX/update clients)

provide the update url

config change UP1 /url <address>:<Port>/<Path>/ /poll 2
config write

Note : This Update client function on the V5 Pbx only works with IE6 not with IE7 or firefox

[[image:Guideline_V5_to_V6_upgrade_Update_clients.png]]

Provide the update file on the Web server for Firmware upgrade

mod cmd UP0 prot http://<IP address>/<Path>/ip200.bin ireset 0x-xxxxxx
mod cmd UP0 boot http://<IP address>/<Path>/boot200.bin ireset 222

Problem:

After upgrade - you can´t reach the phones in the remote locations anymore (for additional updates )if in the remote location is no local PBX where the phones register too.

Because after the Update to V6 the Gatekeeper entry is lost in the phones- so the phones need to connect to the Pbx via Broadcast.

===Phone config===

Send config update for the phones (important ,because of the lost gatekeeper settings), for example:

mod cmd UP1 check ser 20071010-1
config change PHONE SIG /prot H323 /gk-addr x.x.x.x /alt-gk x.x.x.x /gk-id name /tones 0
vars create PHONE/USER-CFG/00000 p your function keys like pickup and ldap settings
vars create PHONE/USER-PWD/00000 pc
ireset

===Upgrade===

Then update the Gateway/Pbx (if you have a master slave configuration - update first the master pbx)

Therefore read also the article Upgrade v5 to v6 shown above

===licences===

First Take care of the Licences when upgrading your PBX! – go to the Licence Manager.

Here the Licences are not described in deep ,this is done on the V6 licence document or wiki entries –go to

http://wiki.innovaphone.com/index.php?title=Howto:How_to_create_licenses_for_innovaphone_products_in_version_6

For upgrading the Pbx to V6 you have to PAY a basic Licence – upgrading an V5 Pbx to V6 PBX is not for Free!!!

The old V5 Trial Lics are not working with V6.

In V6 you have new trial licences if you need them go to

http://download.innovaphone.com/ice/6.00/trial.php

So after upgrade put in your licences again (make sure you bind your licences to the mac address- otherwise they won´t work )

===Extern Object===

There is a new mechanism for the EXTERN Object.

This is pretty much enhanced compared to the implementation in V5.

Now, a PBX will try to deliver a call if unknown send it to its up-nodes-tree-master.

If it returns back from there with "unassigned number" cause code send it to the extern object.

To configure on every Pbx (in the Numbering Node) a own EXTERN user and set it also in the Pbx /General at Route root node external calls to and/or route node external calls to.

The Extern Object can be now any Object - but there is only one Extern for the whole root node .

Alslo you can define for every Node an own Extern Obejct.

[[image:Guideline_V5_to_V6_upgrade_Node.png]]

===Locations Concept in V5===

The name Locations Concept as it is in V5 is obsolete - in V6 we call it Numbering Node

If you have more Pbx´s configured as Locations Concept in V5 - and every Pbx has an own Trunk Local object (locally registered) - in V6 it works different.

How to configure this in V6 (that you have on every site an own Trunk Object with the same Number (e.g 0) please read therefore:

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

so when upgrading to V6 you need to reconfigure this.

If you have this scenario (this was in v5 impossible):

Having more innovaphone locations. On every site (location) is an innovaphone gateway with ISDN connection (local ISDN trunk) and more nodes over all locations. That means it is possible to have same phone extensions over different nodes. Every endpoint dials only the extension in-between the own node- if its to reach another node the prefix of this node has to be dialed too.

Also every endpoint dials the trunk line number (e.g 0) and gets a local break out.

go to :

[[Howto:How to configure numbering node with X nodes and X pbx.]]

===MOH===

If you use an External MOH source you have to reconfigure the MOH. As with the _EXTERN_ user there exists also no _MOH_ user anymore.

The configuration of the external MOH is now very much simplified.

Configure the Music on Hold URL in Pbx/General /Music on Hold URL.

You have to add "&coder=G729" or "&coder=G711" or if you use two coder "&coder=G711,G729" or whatever you codec is to the URL you have for the MOH.

The MOH url in V6 is different to the Moh Url in V5

in V6 it looks like this: http://x.x.x./path/filename.$coder?coder=g711a,g729

===Waiting Queue===

Also in the waiting queue you need to change the urls as shown above

===Unnecessary routes===

Delete the routes to http and the user in the pbx for that route - you can delete all the routes and Gw´s what you needed for the MOH in V5 simplifies your configuration and save Gateways.

===Node===

Phones cannot register if no Location (Pbx Name) is configured

In V5 the default location was 'LOC'

In V6 the default location is '.'

So if a V5 was used without configuration of a location all users are configured for the location 'LOC'.

If you configure this location explicitly in your V6 config, the phones register again.

Pbx/General/Pbx Name – here enter the LOC

==Related Articles==

[[Reference:Update Server]]

[[Howto:Upgrade Issues V5 to V6]]

[[Howto:How to create licenses for innovaphone products in version 6]]

[[Howto:How to obtain a V6 test license]]

[[Howto:How to license a standby PBX]]

[[Howto:How to configure a Numbering Scheme with one Node and more Pbx/Locations]]

[[Howto:How to configure numbering node with X nodes and X pbx.]]

[[Category:AdminLog|{{PAGENAME}}]]

[[Category:Howto|{{PAGENAME}}]]