innovaphone wiki - User contributions [en]

Howto:V6 and V7 on IP21, IP200 (old), IP202 and IP400

2008-03-04T09:21:25Z

Mh-TLK: /* Running V6 SR2 */

Due to flash and dram memory limitations, full the V6 feature set is not available on some older innovaphone platforms. You should generally consider replacing IP400 by IP305, as well as IP202 by a combination of IP110/IP200 and IP302.

==Applies To==
This information applies to

* IP400
* IP21
* IP200 (the old one, not IP200A, see label on the back)
* IP202

==More Information==
=== Running V6 up to and including V6 SR1 ===
On all IP400, all IP21 and IP202 with 8 MB Ram and 2MB Flash (see the info screen for details on how much memory your IP202 features), the V6 PBX will not run. The IP400 and IP21 firmware thus does not include the PBX at all.
For the IP202, there are 2 downloads available, '''ip202.bin''' which includes the PBX and '''ip202phone.bin''' which does not. '''ip202.bin''' will not work on older IP202 platforms with only 2MB flash memory.

The V6 Gateway/Gatekeeper - aka “Relay” - will still work on IP400 and IP21, but not on the smaller IP202 (in fact, the '''ip202phone.bin''' is identical to the '''ip200.bin''').

You can check the size of flash/dram at the webinterface of your unit (General -> Info). A line like '''Version V5.01 sr1-hotfix IP202[05-5874], Bootcode[336], HW[224] ''4096''/''8192''''' indicates 4MB flash and 8MB dram.

<center>
{| border=1
|+V6 PBX compatibility for old devices
!width=160|
!width=150|V5 Gateway and PBX
!width=100|V6 Gateway
!width=100|V6 PBX
|----
|IP21
|Yes
|Yes
|No
|----
|IP400
|Yes
|Yes
|No
|----
|IP202 with 2MB Flash
|Yes
|Yes
|No
|----
|IP202 with 4MB Flash
|Yes
|Yes
|Yes
|}
</center>

=== Running V6 SR2 ===
From V6 SR2, there are addtional limitations.

The IP200 (not IP200A) will include neither PPP nor NAT (this means no PPTP and PPPoE either). The phone can thus not be used as a router anymore.

The IP400 does not include PPP (and thus no PPTP or PPPoE either), NAT, Telnet, Update, Aping, TCP-SIP und - as before - the PBX.

[[Category:Faq|{{PAGENAME}}]]

Howto:General information for compact flash cards

2007-12-13T10:04:54Z

Mh-TLK: /* More Information */

==Applies To==
This information applies to

* IP 6000, V6 SR1
* IP 800, V6 SR1
* IP 302/305, V6 SR1

==More Information==

* Which size should the card have?

The card should have at least 64 MB, because it uses FAT32.

* Is there a formula to calculate the space for one mail box user?

Assuming we have G.711, a voice mail (120 seconds maximum) has 960 kByte, because 8 kByte/s are used and assuming we have G.729, a voice mail has 120 kByte, because 1 kByte/s is used.
So it's now on you to estimate the amount of voice mails one of your users will have and how many voice mail users you have.

* Is there a recommended card speed?

No. Also slower cards can be used and there is no advantage to use high speed cards with innovaphone devices.

* Are there recommended manufacturers/cards?

Yes. We recommend to use SanDisk cards, because we made the best experiences with them. But in general, each card should be supported. For SanDisk cards, please use Ultra II or above (Extreme III/IV).

* Is it possible to put MOH on the compact flash card?

Yes, this is possible.

===Known Problems===

* Till now, the ip6000 has problems with certain cf card manufacturers. Please use the recommended Sandisk cards here.

== Related Articles ==

[[Howto:Installing_the_voicemail/music_on_hold_on_a_compact_flash_card | Installing the voicemail/music on hold on a compact flash card]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Which soundcards are supported?

2007-06-27T07:03:07Z

Mh-TLK: /* System Requirements */

== Summary ==
This short document explains which soundcards are supported by innovaphone SoftwarePhone Software.

==Applies To==
This information applies to

* SoftwarePhone, V5.01

==More Information==

=== System Requirements ===

All full-duplex built-in, PCI, ISA or USB soundcards are supported.

[[Category:Faq|{{PAGENAME}}]]