innovaphone wiki - User contributions [en]

Reference:Configuration/DECT/Radio

2009-10-21T16:49:55Z

Mhe:

In this menu, the DECT system can be configured as a '''DECT radio''', provided that a DECT master was already configured.

* '''Disable:''' A checked check box disables the DECT radio (cell).
* '''Master:''' The IP address of the DECT master. If the device itself was defined as the DECT master, then normaly no IP address has to be entered here. If the local IP address 127.0.0.1 is not automatically entered, you have to enter, otherwise on generell-info (welcome-side) in the frame DECT nothing is shown.
* '''Alt Master:''' The IP address of the standby master.
* '''Radio ID:'''
** In '''Singlecell''' operation, the radio ID 0 must be specified.
** In '''Multicell''' operation, every radio must have a unique ID. The ID must lie in the range 0 - Sys-Mask (with Sys-Mask specification) or 0 - 254 (without Sys-Mask specification).
* '''Sync source:''' The radio ID with which the radio is to synchronise.
* '''Alt Sync Source:''' The radio ID with which the radio is to synchronise in the event that the sync master is not accessible. Here, it is to be noted that no loops must be created. In other words, if a sync master exists with the radio ID 1 and an alt sync master exists with the radio ID 3, then the alt sync master must on no account synchronise with any radio, since the radio synchronises with the alt sync master in the event of failure of the sync master.

==Master==
For configuration of DECT-Radios it is needed to specify explicit the ip-address of the DECT-Master here and if present also of the Standby-DECT-Master. Name and Password needs to get configured if the device is only DECT-Radio and not registered to a local DECT-Master. This Name and Password have to be equivalent to Name and Password of the external DECT-Master configured under "Configuration/DECT/System".

==Additional Master==
DECT-Radios can now register to several DECT-Masters and receive their user data. Within this option it is possible to distribute the user data and the registrations to the pbx among the devices.

Howto:Embedded test for phones

2008-09-01T14:20:02Z

Mhe: /* Applies To */

==Applies To==
This information applies to

* IP110, V6
* IP200A/IP210, V6
* IP230, V6
Build 07-60400.01 and later.

Keywords: Funktionstest, Manufacturingtest, Telefontest, Telefonhardware Test, phonehardware test, phone, selftest, phone test, Selbsttest Telefon

==The test==

===Preparation for the Test===
Connect all devices to the telephone where the connection has to be tested. For a full test connect the LAN-Interface to a Switch, the PC-Interface to a PC or another phone, connect the Headset and in case of IP210 and IP230 connect the handset. The IP230 should also be connected to an Extension Module.

===Entering the Test===
To enter the test the following sequence has to be done during idle state of the phone. Press: “Disconnect”, “Arrow Up”, “Arrow Down”, “Disconnect”, Off Hook handset. The time-lag between these actions must not be longer than 2 seconds.
After that you will see the greeting screen of the test.

[[Image:Embedded test for phones 1.PNG|displayscreen]]

At this point you have the choice to enter the Basic or the Full test. The Basic test is for testing the telephone without the Extension Module (Press Menu). The Full Test is for testing the telephone with Extension Module (Press Ok).
If you run the test on a IP210 you will not have the possibility to choose between Basic and Full.

===Running the Test===
Generally speaking: All keys have to be pressed and all Ethernet connections have to be up to finish the test successfully.
Some keys have special features that give the test person the opportunity to check the sound and the configuration of the telephone. These keys are described in the following.
Left Arrow: Status of the LAN link is displayed.
Right Arrow: Status of the PC link is displayed.
Up Arrow: MAC address is displayed.
Down Arrow: Firmware version is displayed.
Ok: Boot code version and programmed Hardware ID is displayed.
Speaker: Plays a scale on the hands-free speaker.
1: Plays a treble beep on the hands-free speaker.
4: Plays a medium beep on the hands-free speaker.
7: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
2: Plays a treble beep on the handset speaker.
5: Plays a medium beep on the handset speaker.
8: Plays a low beep on the handset speaker.
0: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.
3: Plays a treble beep on the headset speaker.
6: Plays a medium beep on the headset speaker.
9: Plays a low beep on the headset speaker.
#: Connects headset microphone and headset speaker. Scratch or blow in the headset microphone and hear a noise in the headset speaker.
Function Keys: Please make sure that all LEDs in the function keys light up after starting the test and switch off after pressing the keys.
Function Keys on Extension Module: Please make sure that all LEDs in the function keys light up after starting the Full test. The LEDs on the Extension Module are switched off by pressing the upper left key on the extension module. NOTE: The test is just for testing the connection to the Extension Module and not for testing the Extension Module itself.
Note: For IP110 the functions behind the keys are not like described above, entering the test is the same, so below the most important functions are described:
+: Plays a treble beep on the hands-free speaker
handsfree-key: Plays a medium beep on the hands-free speaker.
-: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
7: Plays a treble beep on the handset speaker.
8: Plays a medium beep on the handset speaker.
9: Plays a low beep on the handset speaker.
#: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.

===Result of the Test===
After all keys have been pressed and the test person has carefully verified that all LEDs, speakers, microphones and configurations are fine he can on hook the telephone. If the test was successful he will see this screen.

[[Image:Embedded test for phones 2.PNG|displayscreen]]

NOTE: Even if the microphone, speaker or LEDs did not work during the test the result screen will give a successful result. However, the test person has to mark these devices as broken!

[[Category:Howto|{{PAGENAME}}]]

File:Peltor bluetooth headset IP150 wiring diagram 1.jpg

2008-07-30T10:30:02Z

Mhe:

File:Peltor bluetooth headset IP150 all.jpg

2008-07-24T16:32:52Z

Mhe:

File:Peltor bluetooth headset IP150 bridgeconnection.jpg

2008-07-24T16:32:19Z

Mhe:

File:Peltor bluetooth headset IP150 wiring diagram.jpg

2008-07-24T16:31:44Z

Mhe:

File:Peltor bluetooth headset IP150 connection.jpg

2008-07-24T15:52:09Z

Mhe:

File:Peltor bluetooth headset IP150 pinout.jpg

2008-07-24T15:51:45Z

Mhe:

File:Peltor bluetooth headset IP150 verdrahtungsplan.jpg

2008-07-24T15:50:42Z

Mhe:

Howto:Embedded test for phones

2008-07-16T08:27:01Z

Mhe: /* Applies To */

==Applies To==
This information applies to

* IP110, V6
* IP200A/IP210, V6
* IP230, V6
Build 07-60400.01 and later.

Keywords: Funktionstest, Manufacturingtest, Telefontest, Telefonhardware Test, phonehardware test, phone, selftest, phone test

==The test==

===Preparation for the Test===
Connect all devices to the telephone where the connection has to be tested. For a full test connect the LAN-Interface to a Switch, the PC-Interface to a PC or another phone, connect the Headset and in case of IP210 and IP230 connect the handset. The IP230 should also be connected to an Extension Module.

===Entering the Test===
To enter the test the following sequence has to be done during idle state of the phone. Press: “Disconnect”, “Arrow Up”, “Arrow Down”, “Disconnect”, Off Hook handset. The time-lag between these actions must not be longer than 2 seconds.
After that you will see the greeting screen of the test.

[[Image:Embedded test for phones 1.PNG|displayscreen]]

At this point you have the choice to enter the Basic or the Full test. The Basic test is for testing the telephone without the Extension Module (Press Menu). The Full Test is for testing the telephone with Extension Module (Press Ok).
If you run the test on a IP210 you will not have the possibility to choose between Basic and Full.

===Running the Test===
Generally speaking: All keys have to be pressed and all Ethernet connections have to be up to finish the test successfully.
Some keys have special features that give the test person the opportunity to check the sound and the configuration of the telephone. These keys are described in the following.
Left Arrow: Status of the LAN link is displayed.
Right Arrow: Status of the PC link is displayed.
Up Arrow: MAC address is displayed.
Down Arrow: Firmware version is displayed.
Ok: Boot code version and programmed Hardware ID is displayed.
Speaker: Plays a scale on the hands-free speaker.
1: Plays a treble beep on the hands-free speaker.
4: Plays a medium beep on the hands-free speaker.
7: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
2: Plays a treble beep on the handset speaker.
5: Plays a medium beep on the handset speaker.
8: Plays a low beep on the handset speaker.
0: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.
3: Plays a treble beep on the headset speaker.
6: Plays a medium beep on the headset speaker.
9: Plays a low beep on the headset speaker.
#: Connects headset microphone and headset speaker. Scratch or blow in the headset microphone and hear a noise in the headset speaker.
Function Keys: Please make sure that all LEDs in the function keys light up after starting the test and switch off after pressing the keys.
Function Keys on Extension Module: Please make sure that all LEDs in the function keys light up after starting the Full test. The LEDs on the Extension Module are switched off by pressing the upper left key on the extension module. NOTE: The test is just for testing the connection to the Extension Module and not for testing the Extension Module itself.
Note: For IP110 the functions behind the keys are not like described above, entering the test is the same, so below the most important functions are described:
+: Plays a treble beep on the hands-free speaker
handsfree-key: Plays a medium beep on the hands-free speaker.
-: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
7: Plays a treble beep on the handset speaker.
8: Plays a medium beep on the handset speaker.
9: Plays a low beep on the handset speaker.
#: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.

===Result of the Test===
After all keys have been pressed and the test person has carefully verified that all LEDs, speakers, microphones and configurations are fine he can on hook the telephone. If the test was successful he will see this screen.

[[Image:Embedded test for phones 2.PNG|displayscreen]]

NOTE: Even if the microphone, speaker or LEDs did not work during the test the result screen will give a successful result. However, the test person has to mark these devices as broken!

[[Category:Howto|{{PAGENAME}}]]

RMA

2008-06-11T14:53:01Z

Mhe: /* Hints */

==Applies To==
This information applies to the innovaphone device repair procedure.



==More Information==

===Problem Details===
innovaphone entertains a repair service for devices acquired from or through innovaphone. This service is available to innovaphone customers with valid innovaphone account id. Resellers will usually refer to their distributor, end customers to their reseller.

This article describes the access to the new RMA web interface.

===System Requirements===
You need to have a valid innovaphone account id. You will find this e.g. on any invoice received from innovaphone. If you don't have an account, refer to your reseller or distributor for repair.

===Procedure===
To have a device repaired (regardless of warranty), you need to request a returned material autorization (RMA). Devices returned to us without RMA-Id will not be repaired and will returned to you on your expense.

To apply for an RMA-ID, you will visit [http://rma.innovaphone.com rma.innovaphone.com].

This is the information you need to have at hand:

* your innovaphone account id
* the device serial number
* the detailed defect description
* contact data for the person handling the request from an administrational perspective
* contact data for the person handling the request from a technical perspective
* the shipping address for the replacement unit

You need to apply for a separate RMA-Id for each individual device. Bulk submissions with only a single RMA-Id are not accepted.

Upon submission of your request you will receive the RMA-ID. This will be used in all communications to your regarding the issue. The RMA-Id in fact is an issue-ID and you will see all RMA issues in your weekly status overview.

You will be contacted by innovaphone personal regarding the issue (either by email or by phone). This is to avoid unnecessary shipments in case the device can be recovered remotely.

Only when it is determined that the device has to be repaired you may sent it to innovaphone, along with its RMA-Id.

In most cases, a replacement unit will be shipped to you as soon as your RMA shipment is received here. So you will not need to wait for your device to be repaired. Advance Replacement may be available under special support agreement. Contact [mailto:info@innovaphone.com innovaphone representative] for details.

===Hints===
You can bookmark the RMA website at any stage, so you can resume it later or avoid typing your standard data (such as account-id etc.) every time.

When you have completed data entry for one device, you can click on 'Restart' and you will be asked only for the device specific data again for the next device.

If the device in question does not have a serial number (e.g. a headset), then you leave the serial number field empty and enter the description into the '''Device Type''' (not less than four characters) field.

If you only want to return part of a device and have it exchanged with a spare part (e.g. a telephone handset), then you would still enter the affected devices serial number into the serial number field and note this in the '''Detailed defect description''' field.

===Known Problems===
To protect the privacy of your account data, you must enter both matching account number ''and'' ZIP code. However, the ZIP code obviously has to match the ZIP code we have in our records. If this is incorrect for some reasons, this will create a problem. If the form complains about non-matchig account and ZIP code, please try different format (e.g. no spaces at all) or try to leave out parts of the ZIP (e.g. if your ZIP code is '''1234 BC''', try '''1234''' instead).


[[Category:Howto|{{PAGENAME}}]]

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T14:02:15Z

Mhe: /* Known Problems */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==


{{Template:Compat Status "in progress"}}






==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory exists?
|no
|----
|Can be dialled from
|no
|----
|Does CLI resolution
|no
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|yes
|----
|Hands free works fine
|yes
|----
|Volume adjustable during call
|no
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|yes
|----
|Device has programmable function keys
|no
|}

== Known Problems ==
timezone settings can not be received via DHCP,
Cat-cable is connected via screw terminals not via LSA Plus,
installation is quiet filigreed and should only be done by qualified personal,

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T14:01:41Z

Mhe: /* Known Problems */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==


{{Template:Compat Status "in progress"}}






==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory exists?
|no
|----
|Can be dialled from
|no
|----
|Does CLI resolution
|no
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|yes
|----
|Hands free works fine
|yes
|----
|Volume adjustable during call
|no
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|yes
|----
|Device has programmable function keys
|no
|}

== Known Problems ==
timezone settings can not be received via DHCP
Cat-cable is connected via screw terminals not via LSA Plus
installation is quiet filigreed and should only be done by qualified personal

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:34:08Z

Mhe: /* Related Articles */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==


{{Template:Compat Status "in progress"}}






==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory exists?
|no
|----
|Can be dialled from
|no
|----
|Does CLI resolution
|no
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|yes
|----
|Hands free works fine
|yes
|----
|Volume adjustable during call
|no
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|yes
|----
|Device has programmable function keys
|no
|}

== Known Problems ==

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:32:25Z

Mhe: /* Certification Status */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==


{{Template:Compat Status "in progress"}}






==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory exists?
|no
|----
|Can be dialled from
|no
|----
|Does CLI resolution
|no
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|yes
|----
|Hands free works fine
|yes
|----
|Volume adjustable during call
|no
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|yes
|----
|Device has programmable function keys
|no
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:26:13Z

Mhe: /* Keys */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory exists?
|no
|----
|Can be dialled from
|no
|----
|Does CLI resolution
|no
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|yes
|----
|Hands free works fine
|yes
|----
|Volume adjustable during call
|no
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|yes
|----
|Device has programmable function keys
|no
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:25:39Z

Mhe: /* Hands free */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory exists?
|no
|----
|Can be dialled from
|no
|----
|Does CLI resolution
|no
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|yes
|----
|Hands free works fine
|yes
|----
|Volume adjustable during call
|no
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:24:52Z

Mhe: /* Directory */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory exists?
|no
|----
|Can be dialled from
|no
|----
|Does CLI resolution
|no
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:24:02Z

Mhe: /* Directory */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|no
|----
|Can be dialled from
|no
|----
|Does CLI resolution
|no
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:23:39Z

Mhe: /* Broadcast Group & Waiting Queue */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|yes
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|?
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|yes
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|yes
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|?
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:12:10Z

Mhe: /* Hold/Retrieve */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|yes
|----
|Device handles incoming hold (sendonly) correctly
|yes
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|no
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:11:17Z

Mhe: /* DTMF */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|no
|----
|DTMF tones received correctly
|no
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T13:03:24Z

Mhe: /* Basic Call */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|?
|----
|Early media channel
|no
|----
|Device shows called id number
|no
|----
|Device shows called id name
|no
|----
|Device shows called id display info
|no
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|no
|----
|Reverse Media Negotiaton
|?
|----
|Device shows CDPN/CGPN on incoming call
|no
|----
|Device shows CDPN/CGPN on outgoing call
|no
|----
|Device shows connected number
|no
|----
|Device shows diverting number
|no
|----
|Device supports distinctive ringing
|?
|----
|Device supports asymetric codec negotiation
|no
|----
|Device supports codec renegotiation during a conversation
|yes
|----
|Device shows correct display message in case of busy CDPN
|no
|----
|Device shows correct display message in case of not existing CDPN
|no
|----
|Device shows correct display message in case that the call is declined
|no
|----
|Voice Quality OK?
|yes
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|
|----
|DTMF tones received correctly
|
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T12:16:34Z

Mhe: /* Device Setup */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|no
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|no
|----
|Fixed registrations works
|yes
|----
|Device registers w/o Extension (just by name)
|yes
|----
|Device registers by extension
|no
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|no
|----
|Device sends NAT - keepalive messages
|no
|----
|Device refreshes the PBX registration
|yes
|----
|Device supports SIP over TCP
|no
|----
|Device supports SIPS (SIP over TLS)
|no
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|?
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|
|----
|Early media channel
|
|----
|Device shows called id number
|
|----
|Device shows called id name
|
|----
|Device shows called id display info
|
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|
|----
|Reverse Media Negotiaton
|
|----
|Device shows CDPN/CGPN on incoming call
|
|----
|Device shows CDPN/CGPN on outgoing call
|
|----
|Device shows connected number
|
|----
|Device shows diverting number
|
|----
|Device supports distinctive ringing
|
|----
|Device supports asymetric codec negotiation
|
|----
|Device supports codec renegotiation during a conversation
|
|----
|Device shows correct display message in case of busy CDPN
|
|----
|Device shows correct display message in case of not existing CDPN
|
|----
|Device shows correct display message in case that the call is declined
|
|----
|Voice Quality OK?
|
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|
|----
|DTMF tones received correctly
|
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T12:11:35Z

Mhe: /* Device Setup */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|yes
|----
|Device supports magic registration (e.g. by serial)
|
|----
|Fixed registrations works
|
|----
|Device registers w/o Extension (just by name)
|
|----
|Device registers by extension
|
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|
|----
|Device sends NAT - keepalive messages
|
|----
|Device refreshes the PBX registration
|
|----
|Device supports SIP over TCP
|
|----
|Device supports SIPS (SIP over TLS)
|
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|
|----
|Early media channel
|
|----
|Device shows called id number
|
|----
|Device shows called id name
|
|----
|Device shows called id display info
|
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|
|----
|Reverse Media Negotiaton
|
|----
|Device shows CDPN/CGPN on incoming call
|
|----
|Device shows CDPN/CGPN on outgoing call
|
|----
|Device shows connected number
|
|----
|Device shows diverting number
|
|----
|Device supports distinctive ringing
|
|----
|Device supports asymetric codec negotiation
|
|----
|Device supports codec renegotiation during a conversation
|
|----
|Device shows correct display message in case of busy CDPN
|
|----
|Device shows correct display message in case of not existing CDPN
|
|----
|Device shows correct display message in case that the call is declined
|
|----
|Voice Quality OK?
|
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|
|----
|DTMF tones received correctly
|
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-06-02T10:00:37Z

Mhe: /* Device Setup */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|no
|----
|SNTP config has TZ string for timezone/dst autoconfig
|no
|----
|DHCP yields correct default gateway
|
|----
|Device supports magic registration (e.g. by serial)
|
|----
|Fixed registrations works
|
|----
|Device registers w/o Extension (just by name)
|
|----
|Device registers by extension
|
|----
|Device registers with password
|yes
|----
|Device registers multiple identities
|no
|----
|Device supports STUN protocol
|
|----
|Device sends NAT - keepalive messages
|
|----
|Device refreshes the PBX registration
|
|----
|Device supports SIP over TCP
|
|----
|Device supports SIPS (SIP over TLS)
|
|----
|Device supports HTTPS
|no
|----
|Device supports VAD (Voice activity detection)
|
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|
|----
|Early media channel
|
|----
|Device shows called id number
|
|----
|Device shows called id name
|
|----
|Device shows called id display info
|
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|
|----
|Reverse Media Negotiaton
|
|----
|Device shows CDPN/CGPN on incoming call
|
|----
|Device shows CDPN/CGPN on outgoing call
|
|----
|Device shows connected number
|
|----
|Device shows diverting number
|
|----
|Device supports distinctive ringing
|
|----
|Device supports asymetric codec negotiation
|
|----
|Device supports codec renegotiation during a conversation
|
|----
|Device shows correct display message in case of busy CDPN
|
|----
|Device shows correct display message in case of not existing CDPN
|
|----
|Device shows correct display message in case that the call is declined
|
|----
|Voice Quality OK?
|
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|
|----
|DTMF tones received correctly
|
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-05-30T09:03:31Z

Mhe: /* Basic Call */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|
|----
|SNTP config has TZ string for timezone/dst autoconfig
|
|----
|DHCP yields correct default gateway
|
|----
|Device supports magic registration (e.g. by serial)
|
|----
|Fixed registrations works
|
|----
|Device registers w/o Extension (just by name)
|
|----
|Device registers by extension
|
|----
|Device registers with password
|
|----
|Device registers multiple identities
|
|----
|Device supports STUN protocol
|
|----
|Device sends NAT - keepalive messages
|
|----
|Device refreshes the PBX registration
|
|----
|Device supports SIP over TCP
|
|----
|Device supports SIPS (SIP over TLS)
|
|----
|Device supports HTTPS
|
|----
|Device supports VAD (Voice activity detection)
|
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|yes
|----
|call using g711u
|yes
|----
|call using g729
|no
|----
|Overlapped sending
|
|----
|Early media channel
|
|----
|Device shows called id number
|
|----
|Device shows called id name
|
|----
|Device shows called id display info
|
|----
|Fax using T.38
|no
|----
|CGPN can be supressed
|
|----
|Reverse Media Negotiaton
|
|----
|Device shows CDPN/CGPN on incoming call
|
|----
|Device shows CDPN/CGPN on outgoing call
|
|----
|Device shows connected number
|
|----
|Device shows diverting number
|
|----
|Device supports distinctive ringing
|
|----
|Device supports asymetric codec negotiation
|
|----
|Device supports codec renegotiation during a conversation
|
|----
|Device shows correct display message in case of busy CDPN
|
|----
|Device shows correct display message in case of not existing CDPN
|
|----
|Device shows correct display message in case that the call is declined
|
|----
|Voice Quality OK?
|
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|
|----
|DTMF tones received correctly
|
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-05-30T09:02:28Z

Mhe: /* Device Setup */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|
|----
|DHCP is default
|yes
|----
|DHCP yields timeserver and time displays correctly
|
|----
|SNTP config has TZ string for timezone/dst autoconfig
|
|----
|DHCP yields correct default gateway
|
|----
|Device supports magic registration (e.g. by serial)
|
|----
|Fixed registrations works
|
|----
|Device registers w/o Extension (just by name)
|
|----
|Device registers by extension
|
|----
|Device registers with password
|
|----
|Device registers multiple identities
|
|----
|Device supports STUN protocol
|
|----
|Device sends NAT - keepalive messages
|
|----
|Device refreshes the PBX registration
|
|----
|Device supports SIP over TCP
|
|----
|Device supports SIPS (SIP over TLS)
|
|----
|Device supports HTTPS
|
|----
|Device supports VAD (Voice activity detection)
|
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|
|----
|call using g711u
|
|----
|call using g729
|
|----
|Overlapped sending
|
|----
|Early media channel
|
|----
|Device shows called id number
|
|----
|Device shows called id name
|
|----
|Device shows called id display info
|
|----
|Fax using T.38
|
|----
|CGPN can be supressed
|
|----
|Reverse Media Negotiaton
|
|----
|Device shows CDPN/CGPN on incoming call
|
|----
|Device shows CDPN/CGPN on outgoing call
|
|----
|Device shows connected number
|
|----
|Device shows diverting number
|
|----
|Device supports distinctive ringing
|
|----
|Device supports asymetric codec negotiation
|
|----
|Device supports codec renegotiation during a conversation
|
|----
|Device shows correct display message in case of busy CDPN
|
|----
|Device shows correct display message in case of not existing CDPN
|
|----
|Device shows correct display message in case that the call is declined
|
|----
|Voice Quality OK?
|
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|
|----
|DTMF tones received correctly
|
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-05-30T09:01:41Z

Mhe: /* Version */

==Version==
Firmware Version:
0.0.62

Hardware Version:
530v2

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|
|----
|DHCP is default
|
|----
|DHCP yields timeserver and time displays correctly
|
|----
|SNTP config has TZ string for timezone/dst autoconfig
|
|----
|DHCP yields correct default gateway
|
|----
|Device supports magic registration (e.g. by serial)
|
|----
|Fixed registrations works
|
|----
|Device registers w/o Extension (just by name)
|
|----
|Device registers by extension
|
|----
|Device registers with password
|
|----
|Device registers multiple identities
|
|----
|Device supports STUN protocol
|
|----
|Device sends NAT - keepalive messages
|
|----
|Device refreshes the PBX registration
|
|----
|Device supports SIP over TCP
|
|----
|Device supports SIPS (SIP over TLS)
|
|----
|Device supports HTTPS
|
|----
|Device supports VAD (Voice activity detection)
|
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|
|----
|call using g711u
|
|----
|call using g729
|
|----
|Overlapped sending
|
|----
|Early media channel
|
|----
|Device shows called id number
|
|----
|Device shows called id name
|
|----
|Device shows called id display info
|
|----
|Fax using T.38
|
|----
|CGPN can be supressed
|
|----
|Reverse Media Negotiaton
|
|----
|Device shows CDPN/CGPN on incoming call
|
|----
|Device shows CDPN/CGPN on outgoing call
|
|----
|Device shows connected number
|
|----
|Device shows diverting number
|
|----
|Device supports distinctive ringing
|
|----
|Device supports asymetric codec negotiation
|
|----
|Device supports codec renegotiation during a conversation
|
|----
|Device shows correct display message in case of busy CDPN
|
|----
|Device shows correct display message in case of not existing CDPN
|
|----
|Device shows correct display message in case that the call is declined
|
|----
|Voice Quality OK?
|
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|
|----
|DTMF tones received correctly
|
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto6:2N Helios IP - 2N - SIP Testreport

2008-05-29T13:16:38Z

Mhe: New page: ==Version== Firmware Version: 1.0.2.3 Hardware Version: 1.0.0.1 ==Certification Status==   <...

==Version==
Firmware Version:
1.0.2.3

Hardware Version:
1.0.0.1

==Certification Status==









==Device Setup==

{| border="1"
!Tested feature
!Result
|----
|Register Device w/o specific configuration (requires DHCP)
|
|----
|DHCP is default
|
|----
|DHCP yields timeserver and time displays correctly
|
|----
|SNTP config has TZ string for timezone/dst autoconfig
|
|----
|DHCP yields correct default gateway
|
|----
|Device supports magic registration (e.g. by serial)
|
|----
|Fixed registrations works
|
|----
|Device registers w/o Extension (just by name)
|
|----
|Device registers by extension
|
|----
|Device registers with password
|
|----
|Device registers multiple identities
|
|----
|Device supports STUN protocol
|
|----
|Device sends NAT - keepalive messages
|
|----
|Device refreshes the PBX registration
|
|----
|Device supports SIP over TCP
|
|----
|Device supports SIPS (SIP over TLS)
|
|----
|Device supports HTTPS
|
|----
|Device supports VAD (Voice activity detection)
|
|}

==Test Results==

=== Basic Call ===

{| border="1"
!Tested feature
!Result
|----
|call using g711a
|
|----
|call using g711u
|
|----
|call using g729
|
|----
|Overlapped sending
|
|----
|Early media channel
|
|----
|Device shows called id number
|
|----
|Device shows called id name
|
|----
|Device shows called id display info
|
|----
|Fax using T.38
|
|----
|CGPN can be supressed
|
|----
|Reverse Media Negotiaton
|
|----
|Device shows CDPN/CGPN on incoming call
|
|----
|Device shows CDPN/CGPN on outgoing call
|
|----
|Device shows connected number
|
|----
|Device shows diverting number
|
|----
|Device supports distinctive ringing
|
|----
|Device supports asymetric codec negotiation
|
|----
|Device supports codec renegotiation during a conversation
|
|----
|Device shows correct display message in case of busy CDPN
|
|----
|Device shows correct display message in case of not existing CDPN
|
|----
|Device shows correct display message in case that the call is declined
|
|----
|Voice Quality OK?
|
|}

=== DTMF ===

{| border="1"
!Tested feature
!Result
|----
|DTMF tones sent correctly
|
|----
|DTMF tones received correctly
|
|}

=== Hold/Retrieve ===

{| border="1"
!Tested feature
!Result
|----
|Device handles incoming hold (inactive) correctly
|
|----
|Device handles incoming hold (sendonly) correctly
|
|----
|Device can put a call on hold using correctly(inactive or sendonly)
|
|}

=== Transfer with consultation ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Transfer with consultation (alerting only) ===

{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|
|}

=== Blind Transfer ===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Blind Transfer (alerting only)===

{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to testphone.
|
|----
||inno1 calls inno2. inno1 transfers to testphone.
|
|----
|inno1 calls testphone. inno1 transfers to inno2.
|
|----
|inno1 calls testphone. testphone transfers to inno2.
|
|----
|testphone calls inno1. inno1 transfers to inno2.
|
|----
|testphone calls inno1. testphone transfers to inno2.
|
|}

=== Broadcast Group & Waiting Queue ===

{| border="1"
!Tested feature
!Result
|----
|testphone makes call to a Broadcast Group. inno1 picks up.
|
|----
|inno1 makes call to a Broadcast Group. testphone picks up.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up before announcement is played.
|
|----
|testphone makes call to a Waiting Queue. inno1 picks up after announcement is played.
|
|----
||inno1 makes call to a Waiting Queue. testphone picks up.
|
|}

==Other Features==

===Directory===

{| border="1"
!Tested feature
!Result
|----
|Device built-in directory
|----
|Exists
|
|----
|Can be dialled from
|
|----
|Does CLI resolution
|
|}

===Hands free===

{| border="1"
!Tested feature
!Result
|----
|Loudspeaker operation works fine
|
|----
|Hands free works fine
|
|----
|Volume adjustable during call
|
|}

===Keys===

{| border="1"
!Tested feature
!Result
|----
|Device has speed dial keys
|
|----
|Device has programmable function keys
|
|}

== Related Articles ==

Howto:Multi-Party Conferencing with early IP6000

2008-05-15T08:55:41Z

Mhe: /* IP6000 versions that can be upgraded to support multi-party conferencing */

==Applies To==
This information applies to

* IP6000, Hardware builds less than 202



==More Information==
Various innovaphone hardware platforms, including the IP6000, do support [[Reference:Administration/Gateway/Interfaces#Conferencing_interface_.28CONF.29|multi-party conferencing]]. However, early hardware version of the IP6000 do not.

=== IP6000 versions that support multi-party conferencing ===
Hardware builds 202 and up do support it.

=== IP6000 versions that do not support multi-party conferencing ===
Hardware builds prior to 104 do not support it.

=== IP6000 versions that can be upgraded to support multi-party conferencing ===
Hardware builds 104 up to and not including 202, do not support it. However, they can be upgradet to support it.

If you are interested in having your device upgraded, then you need to order item no. 06-00099-020. The price is 290,- € plus shipping. Contact your innovaphone sales representative for details.

==== Procedure ====
To have a box upgraded, send an order for item 06-00099-020. Then submit an [http://rma.innovaphone.com RMA request] and refer to your order within the description field. Tick the "I want this device back" check-button.

== Related Articles ==
[[Reference:Administration/Gateway/Interfaces]]

[[Reference:Administration/PBX/Objects/Call Broadcast Conference]]



[[Category:Faq|{{PAGENAME}}]]

Howto:Multi-Party Conferencing with early IP6000

2008-05-15T08:55:25Z

Mhe: /* IP6000 versions that do not support multi-party conferencing */

==Applies To==
This information applies to

* IP6000, Hardware builds less than 202



==More Information==
Various innovaphone hardware platforms, including the IP6000, do support [[Reference:Administration/Gateway/Interfaces#Conferencing_interface_.28CONF.29|multi-party conferencing]]. However, early hardware version of the IP6000 do not.

=== IP6000 versions that support multi-party conferencing ===
Hardware builds 202 and up do support it.

=== IP6000 versions that do not support multi-party conferencing ===
Hardware builds prior to 104 do not support it.

=== IP6000 versions that can be upgraded to support multi-party conferencing ===
Hardware builds 105 up to and not including 202, do not support it. However, they can be upgradet to support it.

If you are interested in having your device upgraded, then you need to order item no. 06-00099-020. The price is 290,- € plus shipping. Contact your innovaphone sales representative for details.

==== Procedure ====
To have a box upgraded, send an order for item 06-00099-020. Then submit an [http://rma.innovaphone.com RMA request] and refer to your order within the description field. Tick the "I want this device back" check-button.

== Related Articles ==
[[Reference:Administration/Gateway/Interfaces]]

[[Reference:Administration/PBX/Objects/Call Broadcast Conference]]



[[Category:Faq|{{PAGENAME}}]]

Howto:What is the power draw (in Watts) of the telephones IP230, IP200 and IP110 using PoE?

2008-03-03T13:50:50Z

Mhe:

The IP110,IP200A,IP230 Phones support POE Class 1

Poe Class 1 (according to IEEE 802.3af) describes maximum Watt output from 0,44 W - 3,84 W

[[Category:Faq|{{PAGENAME}}]]

Howto:How to Reset IPXXX

2007-09-28T13:14:58Z

Mhe: /* More Information */

==Summary==
Different Reset Options of IPXXX

==Applies To==
This information applies to

* All innovaphone products with the latest boot code.

==More Information==
Different options resetting innovaphone devices.

* bringing to Factory default
* bringing to TFTP mode for GWLoad
* clearing config
* explaining the Led behavior

Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230

Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table. If you want to reanimate this devices now with GWLoad, do not powercycle the device again. If the factory reset was successful the device is now in the defined TFTP-Mode and ready for GWLoad. If you just wanted to factory reset the device you can do a powercycle for sure.

If the factory reset was not successful please contact rma@innovaphone.com

{| border=1
!Device (visual display)
!Reset Button/key
!Button pressed
!Clear Config
Firmware
Boot code update
!Pressing Button to TFTP without deleting config in seconds ca.
!Pressing Button to factory reset in seconds ca.
!GWLoad- / TFTP-Mode
!Firmware starting
!Firmware ready
!Firmware Error
|----
|IP21 (all LEDs)
|Button
|ready: <5s blink, >5s constant flash

line1+ line2 + door + aux constant flash / link + act off

with plugged in Ethernet cable 100M + link: <3s off, >3s normal operating state
|...

ready fast blink, line1 + line2 + door + aux off link + 100M normal operating

|3
|25
|all Led’s are constant flashing

Link is blinking
|ready + line1/2 + door+ aux + 100M(if link)

permanent for ca. 5s

link blinking
|ready + 100M (if link)

link blinking
|
|----
|IP400 (all Led’s)
|Button
|PPP+Tel.1+Tel.2: < 5s blink, [5;8] constant flash, >8 ready + link + act constant flash

without Ethernet cable plugged in: <8s off, 8s one blink, >8s off
|
|3
|25
|Ready + Link + Act flashing constant
|<8 Ready + PPP + Tel1 + Tel2 constant flash,

[3;10] link + act. uncoordinated flashing

>10s Ready + link (if link) constant act. blinking
|Ready + 100M (if link)

link blinking
|
|----
|IP3000 (all Led’s)
|Button
|<6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,

act + speed + link off

>10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off

with Ethernet cable plugged in: act + speed + link normal working state
|Fast blink (green)
|3
|25
|all Led’s flashing permanent

ready off

link blinking
|>2 link + speed constant flashing, act blinking

<5s PRI1 + PRI2 + S/T constant flash

>5s ready constant flash, (if link) link + speed constant flashing, act blinking
|ready constant flash, (if link) link + speed constant flashing, act blinking
|Blinking (green)
|----
|IP800 / IP6000

(red/green/orange ready LED )
|Button
|<6 slow gn blink

[6;10] constant red

[10;13] fast gn blink

<13 constant orange
|Fast blink (green)
|3
|15 (IP800)

15-20 (IP6000)
|constant orange
|Red
|Green
|Blinking (red)
|----
|IP1200
|Button
|<2s Alarm red constant flash, ready off

[2;7] Alarm off, ready slow green blink

[7;13] Alarm off, read fast blink green

>13s Alarm off, ready 2 Hz blink green
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|<2s Alarm red constant flash

ready green constant flash

Power orange constant flash

[2;4] Alarm off, ready off, Power orange

>4s Alarm off, ready constant green flash, Power constant green flash
|Ready constant green flash and power constant orange flash
|Alarm (red)
|----
|IP200/IP202 (red handset)
|Alt key
|Slow blink
|Slow blink
|3
|5
|Constant flash
|Slow blink
|Off
|Constant flash
|----
|IP200A/IP210 (red handset)
|Alt key
|Slow blink
|Fast blink
|3
|15
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP230 (Menu key)
|Menu key
|Slow blink
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP110 (Led’s in F1-F4 key)
|Save key
|Slow blink
|F1-F4 off
|3
|10 - 15
|Slow flash ca. 2 Hz
|constant F1 flash
|Off
|Blinking
|}

== Related Articles ==
[[Howto:How to use gwload]]

[[Category:Howto|{{PAGENAME}}]]

Howto:Embedded test for phones

2007-07-20T13:21:28Z

Mhe: /* Applies To */

==Applies To==
This information applies to

* IP110, V6
* IP200A/IP210, V6
* IP230, V6
Build 07-60400.01 and later.

Keywords: Funktionstest, Manufacturingtest, Telefontest, Telefonhardware Test, phonehardware test

==The test==

===Preparation for the Test===
Connect all devices to the telephone where the connection has to be tested. For a full test connect the LAN-Interface to a Switch, the PC-Interface to a PC or another phone, connect the Headset and in case of IP210 and IP230 connect the handset. The IP230 should also be connected to an Extension Module.

===Entering the Test===
To enter the test the following sequence has to be done during idle state of the phone. Press: “Disconnect”, “Arrow Up”, “Arrow Down”, “Disconnect”, Off Hook handset. The time-lag between these actions must not be longer than 2 seconds.
After that you will see the greeting screen of the test.

[[Image:Embedded test for phones 1.PNG|displayscreen]]

At this point you have the choice to enter the Basic or the Full test. The Basic test is for testing the telephone without the Extension Module (Press Menu). The Full Test is for testing the telephone with Extension Module (Press Ok).
If you run the test on a IP210 you will not have the possibility to choose between Basic and Full.

===Running the Test===
Generally speaking: All keys have to be pressed and all Ethernet connections have to be up to finish the test successfully.
Some keys have special features that give the test person the opportunity to check the sound and the configuration of the telephone. These keys are described in the following.
Left Arrow: Status of the LAN link is displayed.
Right Arrow: Status of the PC link is displayed.
Up Arrow: MAC address is displayed.
Down Arrow: Firmware version is displayed.
Ok: Boot code version and programmed Hardware ID is displayed.
Speaker: Plays a scale on the hands-free speaker.
1: Plays a treble beep on the hands-free speaker.
4: Plays a medium beep on the hands-free speaker.
7: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
2: Plays a treble beep on the handset speaker.
5: Plays a medium beep on the handset speaker.
8: Plays a low beep on the handset speaker.
0: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.
3: Plays a treble beep on the headset speaker.
6: Plays a medium beep on the headset speaker.
9: Plays a low beep on the headset speaker.
#: Connects headset microphone and headset speaker. Scratch or blow in the headset microphone and hear a noise in the headset speaker.
Function Keys: Please make sure that all LEDs in the function keys light up after starting the test and switch off after pressing the keys.
Function Keys on Extension Module: Please make sure that all LEDs in the function keys light up after starting the Full test. The LEDs on the Extension Module are switched off by pressing the upper left key on the extension module. NOTE: The test is just for testing the connection to the Extension Module and not for testing the Extension Module itself.
Note: For IP110 the functions behind the keys are not like described above, entering the test is the same, so below the most important functions are described:
+: Plays a treble beep on the hands-free speaker
handsfree-key: Plays a medium beep on the hands-free speaker.
-: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
7: Plays a treble beep on the handset speaker.
8: Plays a medium beep on the handset speaker.
9: Plays a low beep on the handset speaker.
#: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.

===Result of the Test===
After all keys have been pressed and the test person has carefully verified that all LEDs, speakers, microphones and configurations are fine he can on hook the telephone. If the test was successful he will see this screen.

[[Image:Embedded test for phones 2.PNG|displayscreen]]

NOTE: Even if the microphone, speaker or LEDs did not work during the test the result screen will give a successful result. However, the test person has to mark these devices as broken!

[[Category:Howto|{{PAGENAME}}]]

Howto:Embedded test for phones

2007-07-20T13:18:16Z

Mhe:

==Applies To==
This information applies to

* IP110, V6
* IP210, V6
* IP230, V6
Build 07-60400.01 and later.

Keywords: Funktionstest, Manufacturingtest, Telefontest, Telefonhardware Test, phonehardware test

==The test==

===Preparation for the Test===
Connect all devices to the telephone where the connection has to be tested. For a full test connect the LAN-Interface to a Switch, the PC-Interface to a PC or another phone, connect the Headset and in case of IP210 and IP230 connect the handset. The IP230 should also be connected to an Extension Module.

===Entering the Test===
To enter the test the following sequence has to be done during idle state of the phone. Press: “Disconnect”, “Arrow Up”, “Arrow Down”, “Disconnect”, Off Hook handset. The time-lag between these actions must not be longer than 2 seconds.
After that you will see the greeting screen of the test.

[[Image:Embedded test for phones 1.PNG|displayscreen]]

At this point you have the choice to enter the Basic or the Full test. The Basic test is for testing the telephone without the Extension Module (Press Menu). The Full Test is for testing the telephone with Extension Module (Press Ok).
If you run the test on a IP210 you will not have the possibility to choose between Basic and Full.

===Running the Test===
Generally speaking: All keys have to be pressed and all Ethernet connections have to be up to finish the test successfully.
Some keys have special features that give the test person the opportunity to check the sound and the configuration of the telephone. These keys are described in the following.
Left Arrow: Status of the LAN link is displayed.
Right Arrow: Status of the PC link is displayed.
Up Arrow: MAC address is displayed.
Down Arrow: Firmware version is displayed.
Ok: Boot code version and programmed Hardware ID is displayed.
Speaker: Plays a scale on the hands-free speaker.
1: Plays a treble beep on the hands-free speaker.
4: Plays a medium beep on the hands-free speaker.
7: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
2: Plays a treble beep on the handset speaker.
5: Plays a medium beep on the handset speaker.
8: Plays a low beep on the handset speaker.
0: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.
3: Plays a treble beep on the headset speaker.
6: Plays a medium beep on the headset speaker.
9: Plays a low beep on the headset speaker.
#: Connects headset microphone and headset speaker. Scratch or blow in the headset microphone and hear a noise in the headset speaker.
Function Keys: Please make sure that all LEDs in the function keys light up after starting the test and switch off after pressing the keys.
Function Keys on Extension Module: Please make sure that all LEDs in the function keys light up after starting the Full test. The LEDs on the Extension Module are switched off by pressing the upper left key on the extension module. NOTE: The test is just for testing the connection to the Extension Module and not for testing the Extension Module itself.
Note: For IP110 the functions behind the keys are not like described above, entering the test is the same, so below the most important functions are described:
+: Plays a treble beep on the hands-free speaker
handsfree-key: Plays a medium beep on the hands-free speaker.
-: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
7: Plays a treble beep on the handset speaker.
8: Plays a medium beep on the handset speaker.
9: Plays a low beep on the handset speaker.
#: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.

===Result of the Test===
After all keys have been pressed and the test person has carefully verified that all LEDs, speakers, microphones and configurations are fine he can on hook the telephone. If the test was successful he will see this screen.

[[Image:Embedded test for phones 2.PNG|displayscreen]]

NOTE: Even if the microphone, speaker or LEDs did not work during the test the result screen will give a successful result. However, the test person has to mark these devices as broken!

[[Category:Howto|{{PAGENAME}}]]

Howto:Embedded test for phones

2007-07-20T12:54:25Z

Mhe: New page: ==Applies To== This information applies to * IP110, V6 * IP210, V6 * IP230, V6 Build 07-60400.01 and later. Keywords: Funktionstest, Manufacturingtest, Telefontest, Telefonhardware Test,...

==Applies To==
This information applies to

* IP110, V6
* IP210, V6
* IP230, V6
Build 07-60400.01 and later.

Keywords: Funktionstest, Manufacturingtest, Telefontest, Telefonhardware Test, phonehardware test

==The test==

===Preparation for the Test===
Connect all devices to the telephone where the connection has to be tested. For a full test connect the LAN-Interface to a Switch, the PC-Interface to a PC or another phone, connect the Headset and in case of IP210 and IP230 connect the handset. The IP230 should also be connected to an Extension Module.

===Entering the Test===
To enter the test the following sequence has to be done during idle state of the phone. Press: “Disconnect”, “Arrow Up”, “Arrow Down”, “Disconnect”, Off Hook handset. The time-lag between these actions must not be longer than 2 seconds.
After that you will see the greeting screen of the test.

[[Image:Embedded test for phones 1.PNG|displayscreen]]

At this point you have the choice to enter the Basic or the Full test. The Basic test is for testing the telephone without the Extension Module (Press Menu). The Full Test is for testing the telephone with Extension Module (Press Ok).
If you run the test on a IP210 you will not have the possibility to choose between Basic and Full.

===Running the Test===
Generally speaking: All keys have to be pressed and all Ethernet connections have to be up to finish the test successfully.
Some keys have special features that give the test person the opportunity to check the sound and the configuration of the telephone. These keys are described in the following.
Left Arrow: Status of the LAN link is displayed.
Right Arrow: Status of the PC link is displayed.
Up Arrow: MAC address is displayed.
Down Arrow: Firmware version is displayed.
Ok: Boot code version and programmed Hardware ID is displayed.
Speaker: Plays a scale on the hands-free speaker.
1: Plays a treble beep on the hands-free speaker.
4: Plays a medium beep on the hands-free speaker.
7: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
2: Plays a treble beep on the handset speaker.
5: Plays a medium beep on the handset speaker.
8: Plays a low beep on the handset speaker.
0: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.
3: Plays a treble beep on the headset speaker.
6: Plays a medium beep on the headset speaker.
9: Plays a low beep on the headset speaker.
#: Connects headset microphone and headset speaker. Scratch or blow in the headset microphone and hear a noise in the headset speaker.
Function Keys: Please make sure that all LEDs in the function keys light up after starting the test and switch off after pressing the keys.
Function Keys on Extension Module: Please make sure that all LEDs in the function keys light up after starting the Full test. The LEDs on the Extension Module are switched off by pressing the upper left key on the extension module. NOTE: The test is just for testing the connection to the Extension Module and not for testing the Extension Module itself.
Note: For IP110 the functions behind the keys are not like described above, entering the test is the same, so below the most important functions are described:
+: Plays a treble beep on the hands-free speaker
handsfree-key: Plays a medium beep on the hands-free speaker.
-: Plays a low beep on the hands-free speaker.
*: Connects hands-free microphone and hands-free speaker. Scratch or blow in the hands-free microphone and hear a noise in the hands-free speaker.
7: Plays a treble beep on the handset speaker.
8: Plays a medium beep on the handset speaker.
9: Plays a low beep on the handset speaker.
#: Connects handset microphone and handset speaker. Scratch or blow in the handset microphone and hear a noise in the handset speaker.

===Result of the Test===
After all keys have been pressed and the test person has carefully verified that all LEDs, speakers, microphones and configurations are fine he can on hook the telephone. If the test was successful he will see this screen.

===Known Problems===



[[Category:Howto|{{PAGENAME}}]]

File:Embedded test for phones 2.PNG

2007-07-20T12:52:22Z

Mhe:

File:Embedded test for phones 1.PNG

2007-07-20T12:19:39Z

Mhe:

Howto:How to Reset IPXXX

2007-05-11T13:50:26Z

Mhe:

==Summary==
Different Reset Options of IPXXX

==Applies To==
This information applies to

* All innovaphone products with the latest boot code.

==More Information==
Different options resetting innovaphone devices.

* bringing to Factory default
* bringing to TFTP mode for GWLoad
* clearing config
* explaining the Led behavior

Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230

Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table.

{| border=1
!Device (visual display)
!Reset Button/key
!Button pressed
!Clear Config
Firmware
Boot code update
!Pressing Button to TFTP without deleting config in seconds ca.
!Pressing Button to factory reset in seconds ca.
!GWLoad- / TFTP-Mode
!Firmware starting
!Firmware ready
!Firmware Error
|----
|IP21 (all LEDs)
|Button
|ready: <5s blink, >5s constant flash

line1+ line2 + door + aux constant flash / link + act off

with plugged in Ethernet cable 100M + link: <3s off, >3s normal operating state
|...

ready fast blink, line1 + line2 + door + aux off link + 100M normal operating

|3
|25
|all Led’s are constant flashing

Link is blinking
|ready + line1/2 + door+ aux + 100M(if link)

permanent for ca. 5s

link blinking
|ready + 100M (if link)

link blinking
|
|----
|IP400 (all Led’s)
|Button
|PPP+Tel.1+Tel.2: < 5s blink, [5;8] constant flash, >8 ready + link + act constant flash

without Ethernet cable plugged in: <8s off, 8s one blink, >8s off
|
|3
|25
|Ready + Link + Act flashing constant
|<8 Ready + PPP + Tel1 + Tel2 constant flash,

[3;10] link + act. uncoordinated flashing

>10s Ready + link (if link) constant act. blinking
|Ready + 100M (if link)

link blinking
|
|----
|IP3000 (all Led’s)
|Button
|<6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,

act + speed + link off

>10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off

with Ethernet cable plugged in: act + speed + link normal working state
|Fast blink (green)
|3
|25
|all Led’s flashing permanent

ready off

link blinking
|>2 link + speed constant flashing, act blinking

<5s PRI1 + PRI2 + S/T constant flash

>5s ready constant flash, (if link) link + speed constant flashing, act blinking
|ready constant flash, (if link) link + speed constant flashing, act blinking
|Blinking (green)
|----
|IP800 / IP6000

(red/green/orange ready LED )
|Button
|<6 slow gn blink

[6;10] constant red

[10;13] fast gn blink

<13 constant orange
|Fast blink (green)
|3
|15 (IP800)

15-20 (IP6000)
|constant orange
|Red
|Green
|Blinking (red)
|----
|IP1200
|Button
|<2s Alarm red constant flash, ready off

[2;7] Alarm off, ready slow green blink

[7;13] Alarm off, read fast blink green

>13s Alarm off, ready 2 Hz blink green
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|<2s Alarm red constant flash

ready green constant flash

Power orange constant flash

[2;4] Alarm off, ready off, Power orange

>4s Alarm off, ready constant green flash, Power constant green flash
|Ready constant green flash and power constant orange flash
|Alarm (red)
|----
|IP200/IP202 (red handset)
|Alt key
|Slow blink
|Slow blink
|3
|5
|Constant flash
|Slow blink
|Off
|Constant flash
|----
|IP200A/IP210 (red handset)
|Alt key
|Slow blink
|Fast blink
|3
|15
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP230 (Menu key)
|Menu key
|Slow blink
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP110 (Led’s in F1-F4 key)
|Save key
|Slow blink
|F1-F4 off
|3
|10 - 15
|Slow flash ca. 2 Hz
|constant F1 flash
|Off
|Blinking
|}

== Related Articles ==
[[Howto:How to use gwload]]

[[Category:Howto|{{PAGENAME}}]]

Howto:How to Reset IPXXX

2007-05-11T13:33:49Z

Mhe: /* More Information */

==Summary==
Different Reset Options of IPXXX

==Applies To==
This information applies to

* All innovaphone products with the latest boot code.

==More Information==
Different options resetting innovaphone devices.

* bringing to Factory default
* bringing to TFTP mode for GWLoad
* clearing config
* explaining the Led behavior

Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230

Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table.

{| border=1
!Device (visual display)
!Reset Button/key
!Button pressed
!Clear Config
Firmware
Boot code update
!Pressing Button to TFTP without deleting config in seconds ca.
!Pressing Button to factory reset in seconds ca.
!GWLoad- / TFTP-Mode
!Firmware starting
!Firmware ready
!Firmware Error
|----
|IP21 (all LEDs)
|Button
|ready: <5s blink, >5s constant flash

line1+ line2 + door + aux constant flash / link + act off

with plugged in Ethernet cable 100M + link: <3s off, >3s normal operating state
|...

ready fast blink, line1 + line2 + door + aux off link + 100M normal operating

|3
|25
|all Led’s are constant flashing

Link is blinking
|ready + line1/2 + door+ aux + 100M(if link)

permanent for ca. 5s

link blinking
|ready + 100M (if link)

link blinking
|
|----
|IP400 (all Led’s)
|Button
|PPP+Tel.1+Tel.2: < 5s blink, [5;8] constant flash, >8 ready + link + act constant flash

without Ethernet cable plugged in: <8s off, 8s one blink, >8s off
|
|3
|25
|Ready + Link + Act flashing constant
|<8 Ready + PPP + Tel1 + Tel2 constant flash,

[3;10] link + act. uncoordinated flashing

>10s Ready + link (if link) constant act. blinking
|Ready + 100M (if link)

link blinking
|
|----
|IP3000 (all Led’s)
|Button
|<6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,

act + speed + link off

>10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off

with Ethernet cable plugged in: act + speed + link normal working state
|Fast blink (green)
|3
|25
|all Led’s flashing permanent

ready off

link blinking
|>2 link + speed constant flashing, act blinking

<5s PRI1 + PRI2 + S/T constant flash

>5s ready constant flash, (if link) link + speed constant flashing, act blinking
|ready constant flash, (if link) link + speed constant flashing, act blinking
|Blinking (green)
|----
|IP800 / IP6000

(red/green/orange ready LED )
|Button
|<6 slow gn blink

[6;10] constant red

[10;13] fast gn blink

<13 constant orange
|Fast blink (green)
|3
|15 (IP800)

15-20 (IP6000)
|constant orange
|Red
|Green
|Blinking (red)
|----
|IP1200
|Button
|<2s Alarm red constant flash, ready off

[2;7] Alarm off, ready slow green blink

[7;13] Alarm off, read fast blink green

>13s Alarm off, ready 2 Hz blink green
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|<2s Alarm red constant flash

ready green constant flash

Power orange constant flash

[2;4] Alarm off, ready off, Power orange

>4s Alarm off, ready constant green flash, Power constant green flash
|Ready constant green flash and power constant orange flash
|Alarm (red)
|----
|IP200/IP202 (red handset)
|Alt key
|Slow blink
|Slow blink
|3
|5
|Constant flash
|Slow blink
|Off
|Constant flash
|----
|IP200A/IP210 (red handset)
|Alt key
|Slow blink
|Fast blink
|3
|15
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP230 (Menu key)
|Menu key
|Slow blink
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP110 (Led’s in F1-F4 key)
|Save key
|Slow blink
|F1-F4 off
|3
|10 - 15
|Slow flash ca. 2 Hz
|constant F1 flash
|Off
|Blinking
|}

[[Category:Howto|{{PAGENAME}}]]

Howto:How to Reset IPXXX

2007-05-11T13:33:13Z

Mhe: /* More Information */

==Summary==
Different Reset Options of IPXXX

==Applies To==
This information applies to

* All innovaphone products with the latest boot code.

==More Information==
Different options resetting innovaphone products.

* bringing to Factory default
* bringing to TFTP mode for GWLoad
* clearing config
* explaining the Led behavior

Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230

Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table.

{| border=1
!Device (visual display)
!Reset Button/key
!Button pressed
!Clear Config
Firmware
Boot code update
!Pressing Button to TFTP without deleting config in seconds ca.
!Pressing Button to factory reset in seconds ca.
!GWLoad- / TFTP-Mode
!Firmware starting
!Firmware ready
!Firmware Error
|----
|IP21 (all LEDs)
|Button
|ready: <5s blink, >5s constant flash

line1+ line2 + door + aux constant flash / link + act off

with plugged in Ethernet cable 100M + link: <3s off, >3s normal operating state
|...

ready fast blink, line1 + line2 + door + aux off link + 100M normal operating

|3
|25
|all Led’s are constant flashing

Link is blinking
|ready + line1/2 + door+ aux + 100M(if link)

permanent for ca. 5s

link blinking
|ready + 100M (if link)

link blinking
|
|----
|IP400 (all Led’s)
|Button
|PPP+Tel.1+Tel.2: < 5s blink, [5;8] constant flash, >8 ready + link + act constant flash

without Ethernet cable plugged in: <8s off, 8s one blink, >8s off
|
|3
|25
|Ready + Link + Act flashing constant
|<8 Ready + PPP + Tel1 + Tel2 constant flash,

[3;10] link + act. uncoordinated flashing

>10s Ready + link (if link) constant act. blinking
|Ready + 100M (if link)

link blinking
|
|----
|IP3000 (all Led’s)
|Button
|<6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,

act + speed + link off

>10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off

with Ethernet cable plugged in: act + speed + link normal working state
|Fast blink (green)
|3
|25
|all Led’s flashing permanent

ready off

link blinking
|>2 link + speed constant flashing, act blinking

<5s PRI1 + PRI2 + S/T constant flash

>5s ready constant flash, (if link) link + speed constant flashing, act blinking
|ready constant flash, (if link) link + speed constant flashing, act blinking
|Blinking (green)
|----
|IP800 / IP6000

(red/green/orange ready LED )
|Button
|<6 slow gn blink

[6;10] constant red

[10;13] fast gn blink

<13 constant orange
|Fast blink (green)
|3
|15 (IP800)

15-20 (IP6000)
|constant orange
|Red
|Green
|Blinking (red)
|----
|IP1200
|Button
|<2s Alarm red constant flash, ready off

[2;7] Alarm off, ready slow green blink

[7;13] Alarm off, read fast blink green

>13s Alarm off, ready 2 Hz blink green
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|<2s Alarm red constant flash

ready green constant flash

Power orange constant flash

[2;4] Alarm off, ready off, Power orange

>4s Alarm off, ready constant green flash, Power constant green flash
|Ready constant green flash and power constant orange flash
|Alarm (red)
|----
|IP200/IP202 (red handset)
|Alt key
|Slow blink
|Slow blink
|3
|5
|Constant flash
|Slow blink
|Off
|Constant flash
|----
|IP200A/IP210 (red handset)
|Alt key
|Slow blink
|Fast blink
|3
|15
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP230 (Menu key)
|Menu key
|Slow blink
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP110 (Led’s in F1-F4 key)
|Save key
|Slow blink
|F1-F4 off
|3
|10 - 15
|Slow flash ca. 2 Hz
|constant F1 flash
|Off
|Blinking
|}

[[Category:Howto|{{PAGENAME}}]]

Howto:How to Reset IPXXX

2007-05-11T13:29:05Z

Mhe: /* More Information */

==Summary==
Different Reset Options of IPXXX

==Applies To==
This information applies to

* All innovaphone products with the latest boot code.

==More Information==
Different options resetting innovaphone products.

* bringing to Factory default
* clear config
* bringing to tftp mode for Gwload
* explaining the Led behavior

Additional Information for the following table, factory default for the phones IP110, IP150, IP200, IP202, IP230

Seperating the phone from the power,press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table.

{| border=1
!Device (visual display)
!Reset Button/key
!Button pressed
!Clear Config
Firmware
Boot code update
!Pressing Button to TFTP without deleting config in seconds ca.
!Pressing Button to factory reset in seconds ca.
!GWLoad- / TFTP-Mode
!Firmware starting
!Firmware ready
!Firmware Error
|----
|IP21 (all LEDs)
|Button
|ready: <5s blink, >5s constant flash

line1+ line2 + door + aux constant flash / link + act off

with plugged in Ethernet cable 100M + link: <3s off, >3s normal operating state
|...

ready fast blink, line1 + line2 + door + aux off link + 100M normal operating

|3
|25
|all Led’s are constant flashing

Link is blinking
|ready + line1/2 + door+ aux + 100M(if link)

permanent for ca. 5s

link blinking
|ready + 100M (if link)

link blinking
|
|----
|IP400 (all Led’s)
|Button
|PPP+Tel.1+Tel.2: < 5s blink, [5;8] constant flash, >8 ready + link + act constant flash

without Ethernet cable plugged in: <8s off, 8s one blink, >8s off
|
|3
|25
|Ready + Link + Act flashing constant
|<8 Ready + PPP + Tel1 + Tel2 constant flash,

[3;10] link + act. uncoordinated flashing

>10s Ready + link (if link) constant act. blinking
|Ready + 100M (if link)

link blinking
|
|----
|IP3000 (all Led’s)
|Button
|<6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,

act + speed + link off

>10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off

with Ethernet cable plugged in: act + speed + link normal working state
|Fast blink (green)
|3
|25
|all Led’s flashing permanent

ready off

link blinking
|>2 link + speed constant flashing, act blinking

<5s PRI1 + PRI2 + S/T constant flash

>5s ready constant flash, (if link) link + speed constant flashing, act blinking
|ready constant flash, (if link) link + speed constant flashing, act blinking
|Blinking (green)
|----
|IP800 / IP6000

(red/green/orange ready LED )
|Button
|<6 slow gn blink

[6;10] constant red

[10;13] fast gn blink

<13 constant orange
|Fast blink (green)
|3
|15 (IP800)

15-20 (IP6000)
|constant orange
|Red
|Green
|Blinking (red)
|----
|IP1200
|Button
|<2s Alarm red constant flash, ready off

[2;7] Alarm off, ready slow green blink

[7;13] Alarm off, read fast blink green

>13s Alarm off, ready 2 Hz blink green
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|<2s Alarm red constant flash

ready green constant flash

Power orange constant flash

[2;4] Alarm off, ready off, Power orange

>4s Alarm off, ready constant green flash, Power constant green flash
|Ready constant green flash and power constant orange flash
|Alarm (red)
|----
|IP200/IP202 (red handset)
|Alt key
|Slow blink
|Slow blink
|3
|5
|Constant flash
|Slow blink
|Off
|Constant flash
|----
|IP200A/IP210 (red handset)
|Alt key
|Slow blink
|Fast blink
|3
|15
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP230 (Menu key)
|Menu key
|Slow blink
|Fast blink
|3
|10
|Slow flash ca. 2 Hz
|On
|Off
|Blinking
|----
|IP110 (Led’s in F1-F4 key)
|Save key
|Slow blink
|F1-F4 off
|3
|10 - 15
|Slow flash ca. 2 Hz
|constant F1 flash
|Off
|Blinking
|}

[[Category:Howto|{{PAGENAME}}]]