innovaphone wiki - User contributions [en]

ReleaseNotes11r1:Firmware

2015-04-16T08:31:34Z

MrOiso: /* NAT: Local addr for outgoing packets was set wrong in case packet matched an inbound mapping an was not sent to ETH0 */

This is the Firmware 11r1 Roadmap Document. 
 
Service Releases are planned for the second monday each month. 
 

This article is generated automatically. Do not edit!
Please see ''[[Support:What is the DVL-Roadmap?|the disclaimer]]'' before using the information presented here!

= 11r1 Service Release 1 (110925) =
Changes included in Version 11r1 Service Release 1
[http://mantis.innovaphone.com/view.php?id=138646 Definition]

== IP232/222/111: Attributes of Partner fkey got lost ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138555 138555]
|}
Attributes of Partner fkey got lost when reconfiguring on the phone ui. "Partner Type" was lost "Show connected Party in busy State" was lost 

== IP222/232/111: Auto-jump to APP_PHONE for overlap-dialing ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138611 138611]
|}
Auto-jump to APP_PHONE for overlap-dialing when using Partner fkey with Partner-Type "Executive". 

== Trap if registered via SIP/TCP and wifi connection was lost ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138695 138695]
|}
This situation caused a narrow loop of socket reconnects resulting in a file descriptor table overflow.

== SIP: Trap when trying to re-connect TCP/TLS connection while network interface is down ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138717 138717]
|}
Trap when trying to re-connect TCP/TLS connection while network interface is down. E.g. while WLAN conectivity is lost. 

== On some devices incoming calls are indicated with delay in SIP/TCP mode ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138773 138773]
|}
Some devices seem to suspend during incoming call signaling and thus it's ringing after a delay. Try to keep the device woke at this point.

== Licenses not working ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138777 138777]
|}
The softwarephone didn't recognize its licenses.

== Microphone and speaker volume not correct ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138784 138784]
|}
On myPBX Android the speaker and microphone volume was not correct since the change where 6dB margin had been introduced for the extended dynamic range of G.722.

== IPVA: Eliminated platform-specific stylesheet tracing.xsl ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138808 138808]
|}
Now using common stylesheet tracing.xsl 

== Support for ICE-lite ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138813 138813]
|}
ICE lite and signaling for it 

== H.323: No Media, if G.729B was the only coder in an offer ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138834 138834]
|}
The coder was removed if silence compression was not enabled and no coder was left. This does not make sense, even if we do not do silence compression, we should signal, that we are able to receive G.729B data. 

== IP222/232/111: Close "Call settings" screen when call comes in ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138870 138870]
|}
Must close "Call settings" screen when call comes in. 

== SIP: Losing registration of a SIP interface if another gateway interface is reconfigured ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138888 138888]
|}
Losing registration of a SIP interface if another gateway interface is reconfigured. SIP stack takes IP address for domain name, starts DNS query, gets NX_DOMAIN response and reports REG-DOWN. 

== Incomplete HTTP responses from HTTP server in certain circumstances ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138895 138895]
|}
It might have happened, that the HTTP server closed the underlying TCP connection before all data could be sent. 

== TLS: ClientHello v2 decode error ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138961 138961]
|}
There was an error when decoding the length field of ClientHello messages in SSL 2.0 format, that is sent by some clients to provide downward compatibility with historic SSL 2.0 servers. This led to a DECODE_ERROR alert when the ClientHelloV2 was bigger than 127 bytes. 

== myPBX-DeviceConnection: possible Trap closing library ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138962 138962]
|}
there is a trap inside this library which could be caused by an incoming request while the library is being closed. Not able to reproduce it.

== IP222/232/111: Skip leading and trailing white space in directory search ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138970 138970]
|}
Skip leading and trailing white space in directory search 

== IP232/222/111: 5 latin letters missing when phone is configured to Estonian ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139148 139148]
|}
C, Q, W, X and Y are not part of the official Estonian alphabet. But C, Q, W, X and Y are used in writing foreign proper names. Added these 5 letters. 

== IP222/232/111: Lamp was not turned off after reminding call was connected via action button ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139171 139171]
|}
Lamp was not turned off after reminding call was connected via action button. 

== SIP: Support for video on media-relay ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139232 139232]
|}
Support for video on media-relay. 

== IP222/232/111: Fix for Trap ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139243 139243]
|}
Fix for Trap. 

== Fkey icons missing on extension module ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139333 139333]
|}
No fkey icons on extension module. 

== SIP: Bad header line in re-INVITE when interworking with UNIFY ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139361 139361]
|}
INVITE sip:1055@10.30.6.202:5061;transport=tls;maddr=10.30.6.202 SIP/2.0 Via: SIP/2.0/TLS 172.20.14.233:5060;branch=z9hG4bK-3F8074F1;rport;alias ... P-Sig-Options: Sending-Complete ST-secure 

== IP222/232/111: CANCEL button missing on config dialog for call forward destination ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139374 139374]
|}
Now there are SAVE and CANCEL buttons on config dialog for call forward destination. 

== Registration using MAC address did not work for some IP240 and IP110 phones ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139391 139391]
|}
The mapping of MAC address to the legacy HW-ID was incorrect for some address ranges. Therefore some IP240 and IP110 phones could not register using MAC address. 

== myPBX: Adding favourite from different domain was not possible if presence was not visible ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139428 139428]
|}
If a monitoring call can be established to an endpoint, it should be possible to add it to the favourites. This did not work if the remote side did not allow to see the presence. 

== IP222/232/111: Results from external directory are now displayed according to config option "Name Attributes" ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139473 139473]
|}
Results from external directory are now displayed according to config option "Name Attributes". 

== IP222/232/111: Results from external directory are now displayed according to config option "Name Attributes" ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139473 139473]
|}
Results from external directory are now displayed according to config option "Name Attributes". 

== IP222/232/111: Calls triggered via Web-UI are always started with CLIR ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139480 139480]
|}
Calls triggered via Web-UI are always started with CLIR. 

== SIP: Media re-negotiation fails in some cases ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139506 139506]
|}
Media re-negotiation fails in some cases. 

== SIP: Problem with reuse of inbound TLS connections ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139546 139546]
|}
Problem with reuse of inbound TLS connections. Occurs when remote SIP client restarts without de-registering. 

== IP222/232: Not able to get screen shot (LCD dump) from second extension module ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139582 139582]
|}
Not able to get screen shot (LCD dump) from second extension module. 

== IP232: Touching message center button while 'voice messages' is displayed triggers call to VM now ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139593 139593]
|}
Touching message center button while 'voice messages' is displayed triggers call to VM now. Nothing happened before. 

== FAX Interface: Hanging calls ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139602 139602]
|}
If a call setup to the FAX interface includes a user-user-information element, the call hangs. This is fixed now.

== NAT: Bad handling of timeout on DNS requests ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139657 139657]
|}
Box starts trying to use 0.0.0.0 as DNS server. 

== In rare cases myPBX Android froze at the beginning or end of a call. ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139690 139690]
|}
If OpenSLES was used as audio API myPBX Android froze in rare cases at the beginning or end of a call.

== IP222/232/111: Could not terminate local 3pty conference with softkey "HOLD" ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139739 139739]
|}
Using softkey HOLD on one call in a local 3pty conference should put the call on hold and leaving the other call as active call. 

== IP222/232/111: Could not delete entries from local directory (phonebook) ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139797 139797]
|}
Could not delete entries from local directory (phonebook). Fails with "Operation gescheitert". 

== Name in self-generated certificate MYPBXA-xxxxxxxxxxxx instead of the bare MAC xxxxxxxxxxxx ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139806 139806]
|}
Could not register at the PBX with H.323/TLS and the MAC as hardware ID because the name in the self-generated certificate was set to MYPBXA-xxxxxxxxxxxx. Create the certificate with the bare MAC xxxxxxxxxxxx.

== Should put myPBX Android calls on hold if a GSM call is initiated or accepted ==

{|
|Status
|Assigned
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139834 139834]
|}
Active calls in myPBX Android should be put on hold automatically if a GSM call is initiated or accepted. A held call in myPBX Android should be retrieved automatically if a GSM call ends.

== SIP: Accept asymmetric SRTP encryption ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139888 139888]
|}
Accept asymmetric SRTP encryption if received answer contains different key type then the previously sent offer. 

== SIP: Wrong "a=sendonly" in SDP offer when interworked from WebRTC client ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139937 139937]
|}
WebRTC clients write "c=IN IP4 0.0.0.0" into their SDP offer. RTP addresses occur in ICE candidates only. Must not take it as a "sendonly" offer. 

== Log medialib event if DNS name of STUN server could not be resolved ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140017 140017]
|}
A medialib event is raised, if the DNS name of the STUN server could not be resolved. 

== Coder configuration ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140059 140059]
|}
The coder configuration for SRTP and keying shouldn't be written if the default values are set. Otherwise if the device firmware is downgraded, the old default values aren't used. This is fixed now. Additional if key exchange is set to none, SRTP option isn't written to set it to the default value.

== SIP: Remove all bindings did not work ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140071 140071]
|}
A REGISTER with "Contact: *" was not handled as it should. 

== IP222/232/111: Could not enter % sign via numeric keys ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140075 140075]
|}
Could not enter % sign via numeric keys. Added % to list of special characters on key "1". 

== IP-DECT: Reverse phone book search configuration ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140086 140086]
|}
The IP-DECT reverse phone book search accepts a configuration with phone number types like e164:H,mobile:M now.

== PBX Waiting: No ringback after no-response CFNR ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140087 140087]
|}
If a CFNR is executed due to no-response timeout when the second announcement is played, the caller does not received ringback 

== IP232/222/111: Not able to configure "%u Messages" as label text for active MWI fkey ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140091 140091]
|}
Not able to configure "%u Messages" as label text for active MWI fkey. 

== IP222/232: Display was vertically out of center ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140201 140201]
|}
Display was vertically out of center. 

== IP232/222/111: Phone lock did not work ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140246 140246]
|}
Hide presence control if phone is locked to keep information from being displayed. Hide call lists if phone is locked. 

== Select myPBX as presence provider on first configuration ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140264 140264]
|}
If myPBX has been installed by a logged administrator account and not inside the user account, the default presence provider hasn't been myPBX. This has been changed now, if no default presence provider has been given by an MSI parameter. 

== IP232/222/111: Potential trap if config file option /app-camera-full-screen is used ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140277 140277]
|}
Trap if config file option /app-camera-full-screen is used and image does not fill phone's screen exactly. config change PHONE FORMS /app-camera-full-screen on 

== PBX, H.323/TLS: A call which failed because of failed TLS, could be indicated as busy ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140294 140294]
|}
A cause code generation was missing and a default of busy was used at one place. 

== PBX SBC Object: Config option for TLS Only was missing ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140350 140350]
|}
To force external devices to register with TLS and valid certificates 

== Video: createwindow method not called properly ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140351 140351]
|}
Windows class was missing and the function failed. 

== IP232/222/111: Could not switch from PHONE app to HOME app using ESC/HOME key ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140358 140358]
|}
Could not switch from PHONE app to HOME app using ESC/HOME key 

== T.38: Trap on disconnect/fax send data collision ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140406 140406]
|}
It could happen that data was sent, even if the socket was already deleted. This caused a trap. 

== H.323: decoding of application payload type wrong ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140410 140410]
|}
It was always read as 0. Did work anyway, because 0 was used. 

== H.323: Call to a Call Broadcast Destination failed under special conditions ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140491 140491]
|}
DTMF dial from a Waiting Queue to a Call Broadcast object with many destinations. This caused special timing in H.323, which created the problem. 

== Phones: Fix for a trap ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140497 140497]
|}
Fix for a trap when R-Key is used 3 times. 1st R-Key jumps into call list. 2nd R-Key starts call first list item. 3rd R-Key stops call. May trap if directory look-up is pending. 

== Video/Collaboration: possible endless loop if socket not bound ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140510 140510]
|}
type error, j=0 instead of j==0 

== PBX Conference: Operator created room without PIN ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140524 140524]
|}
Users can't dial-in in an operator created room without a PIN. This is fixed now.

== PBX: Visibility settings for presence note not working across domains ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140535 140535]
|}
If presence visibility was set, the note was also available, regardless of the presence note visibility flag. 

== Video/Collaboration: ICE compatibility with next Versions ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140554 140554]
|}
hmac_sha1 was wrongly calculated  

== H.323: Registration redirection did not work for H.323/TLS ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140555 140555]
|}
Same address was tried again 

== Gateway: Potential trap on call-transfer/call clear collisions ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140558 140558]
|}
Together with very unlikely timing 

== FAX Interface: Potential hanging call when outgoing call failed ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140559 140559]
|}
Call was hanging under some more special conditions 

== One way audio on Samsung SM-G900F with Android 5.0 ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140575 140575]
|}
This could be fixed by changing the Audio API to OpenSL ES. Therefore use this as default here.

== Setup Wizard: Configure Gateway page broken ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140583 140583]
|}
Input field for trunk number strangely positioned. IE and Chrome only. 

== SIP: Bad SIP-URI encoding in Refer-To header ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140589 140589]
|}
Bad SIP-URI encoding in Refer-To header, but only if userpart string contains blanks. Wrong: Refer-To: <sip:eye+beam@ip800.innovaphone.compat> Right: Refer-To: <sip:eye%20beam@ip800.innovaphone.compat> 

== presence and dialog info are not updated due to wrong subscriptions are deleted ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140600 140600]
|}
presence and dialog info are not updated due to wrong subscriptions are deleted 

== IP232/222/111: Allow destination name to be configured for fkey PARK ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140618 140618]
|}
Only destination number could be configured for fkey PARK. Allow destination name to be configured for fkey PARK. 

== IP232/222/111: Allow destination name to be configured for fkey PARK ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140618 140618]
|}
Only destination number could be configured for fkey PARK. Allow destination name to be configured for fkey PARK. 

== myPBX (WebRTC), Call-Waiting did not work ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140624 140624]
|}
An incoming call, when another call was already active, caused the active call tp be put on hold. 

== Video/Collab QoS: check if qwave library is available ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140631 140631]
|}
If not, no QoS functions will be called. Otherwise Video.dll not found. 

== PBX: UC license could not configured on Number Map or Waiting Queue objects ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140646 140646]
|}
The UC license is not really useful on these objects, but Voicemail is, and it can simplify installation if no seperate Voicemail license has to be ordered for these objects, but the available UC license can be used. 

== IP232/222/111: Fix for trap ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140664 140664]
|}
Trap occured if: 1. setup call completion 2. go to list of pending call completion requests 3. open one pending call completion request 4. go offhook 

== Gateway: For mapping of diverting number only the matching map of the calling party number was used ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140729 140729]
|}
This logic was not useful. Now all calling party number maps are evaluated for the diverting number also. 

== WebDAV: Client started PUT for a file in a non-existing folder ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140770 140770]
|}
Client started PUT for a file in a non-existing folder. Client must check if containing folder exist before starting PUT. RFC 2518 When the PUT operation creates a new non-collection resource all ancestors MUST already exist. If all ancestors do not exist, the method MUST fail with a 409 (Conflict) status code. For example, if resource /a/b/c/d.html is to be created and /a/b/c/ does not exist, then the request must fail. 

== Voicemail: Name Display missing within myPBX ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140773 140773]
|}
MyPBX displayed number info only when calling a voicemail object. 

== Voicemail: Default of '$_divconn' is now 'false' ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140832 140832]
|}
was 'true'. 

== IP111 handset microphone gain too high ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140886 140886]
|}
The handset microphone gain of the IP111 was too high. The peer could hear too much of the local environment noise. Lowered the microphone gain and compensated a bit by increasing the handset speaker gain.

== Gateway: An emergency call should not disconnect another emergency call ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140899 140899]
|}
Should search for non-emergency calls to disconnect and should fail if only emergency calls 

== PBX Session Border Object: Sending DTMF with myPBX did not work for phones registered thru the SBC ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140914 140914]
|}
The flag to indicate DTMF support was not forwarded to the PBX 

== SIP: Poll primary proxy with expires=0 after failover ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=132790 132790]
|}
To improve interop with CUCM: Poll primary proxy with expires=0 after failover. While backup registration is up. After getting responses from primary server again, terminate backup registration before starting to register at primary server with expires>0. 

== SIP: Read multiple Diversion headers and read display name from URI's ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138508 138508]
|}
Read multiple Diversion headers and read display name from URI's 

== IP222/232/111: Allow usage of Partner fkey even when 2 or more calls are active ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=138642 138642]
|}
Allow usage of Partner fkey even when 2 or more calls are active.  

== SIP: Failover to secondary SIP server on failed call attempt ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139694 139694]
|}
Switch to secondary SIP server if INVITE client transaction ends up in timeout. 

== Updated translations ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140252 140252]
|}
New translations

== Phones: Updated text translations ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140254 140254]
|}
New translations

== IP232/222/111: Added PHONE_HIDE_PRESENCE_CONTROL to "Fine grained function hiding" ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140398 140398]
|}
Can hide presence-control now. 

== WebRTC: Eliminate deprecated API calls ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140619 140619]
|}
setLocalDescription now needs success and error callback functions. 

= 11r1 Service Release 2 (110945) =
Changes included in Version 11r1 Service Release 2
[http://mantis.innovaphone.com/view.php?id=140630 Definition]

== SIP: Wrong CDPN in incoming calls ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=139726 139726]
|}
Fix for a change introduced in sr18. 

== H.323: Slowstart MSD procedure should be considered complete only after receiving MSD-ACK ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140586 140586]
|}
For compatibility with some Avaya H.323 equipment the MSD procedure was considered complete when receiving MSD after having sent MSD. This causes now problems, again with Avaya. 

== PBX: New routing option Route Root-Node External Calls to\t ... For calls from local PBX only ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140767 140767]
|}
This allows to send calls to an extern interface on slaves where the call originates rather then to the extern on the master. Can simplify routing in configurations with many legacy PBXs. 

== SIP: Fix for media re-negotiation ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140831 140831]
|}
INVITE without SDP offer was sent out on an interface with media-relay and exclusivce-codec config. Should not happen. 

== IP232/222/111: Text strings changed ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140902 140902]
|}
Text strings changed. "Lokales Telefonbuch" is now called Lokale Kontakte" "Registereingabe" is now called "Neuer Kontakt" 

== WebRTC Softwarephone: Improve tracing ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140904 140904]
|}
* In Chrome instead of error messages "unknow" was displayed. * For incoming Offers, the SDP was printed to the trace twice. 

== SIP: Media re-negotiation during early-media fails ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140947 140947]
|}
Loosing early-media when source of early-media changes. Re-negotiation for new source of early-media fails. Was introduced by fix #139506. 

== Only an IP address could be entered as STUN server from the phone UI ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140956 140956]
|}
As workaround names can be entered for this field via the WebUI.

== ICE: Fixed traces for switching roles ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140961 140961]
|}
In come cases the role was wrong in the following trace: "Role conflict indicated, try switch to controlling". But it's only wrong in the trace. No functional problem. 

== IP222/232/111: Lamp was not turned off after reminding call was dropped by remote side ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140974 140974]
|}
Lamp was not turned off after reminding call was dropped by remote side 

== Gateway: A GW definition without address should do a IP4 discovery ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=140980 140980]
|}
For compatibility with old configurations 

== IP222/232/111: LED attribute got lost on fkey config "Call Forwarding" ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141070 141070]
|}
LED attribute was set via Web-UI. After changing the fkey config on the Phone-UI the LED attribute was lost (off). 

== SIP: Removing garbage data from message body ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141104 141104]
|}
Removing trailing garbage data from message body. 

== Phone: Fkeys (partner/pickup/park) sometimes show long gone calls ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141183 141183]
|}
Fkeys (partner/pickup/park) sometimes show long gone calls. Dialog-infos are not deleted when dialog-subscription is deleted. Dialog-subscriptions are deleted when fkeys are re-configured. 

== NAT: Local addr for outgoing packets was set wrong in case packet matched and inbound mapping an was not sent to ETH0 ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141221 141221]
|}
The local addr was determined based on the remote addr in the mapping, which was 0.0.0.0 

== SIP-IF config got lost if number mapping was changed ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141222 141222]
|}
SIP-IF config was damaged if number mapping was changed. 

== Occasional one way audio introduced with the changes for #139690 ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141234 141234]
|}
Apparently we sometimes timed out waiting for the OpenSLES callback to happen during controlled stop of playback. Afterwards the callback set itself to stopped state immediately after start and thus caused silence at the audio output. The missing initialization to avoid this has been added now.

== IP232/222/111: Could not switch from PHONE app to HOME app using ESC/HOME key in active state ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141278 141278]
|}
Could not switch from PHONE app to HOME app using ESC/HOME key while calls are active. This was explicitely blocked. No good idea. 

== Prompt for presence note with "What I'm doing..." ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141306 141306]
|}
The quick-edit presence note in the home screen was filled with the text "Available" if the user was online and had no presence set. It was not a hint and thus had to be deleted explicitly before entering a text. Now we show the hint "What i'm doing..." again.

== Send logs via e-mail was not working because the mail client could not access the attachment files ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141320 141320]
|}
-

== SIP: Could not handle INVITE with huge SDP body ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141333 141333]
|}
Could not handle INVITE with SDP body bigger than 8kbytes. Now up to 16kbytes are possible. 

== Video: library crashes if empty NAL arrives ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141345 141345]
|}
There was no checking for empty NALs. 

== IP222 IP232 IP241: First RTP packet sometimes has the wrong timestamp ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141390 141390]
|}
One packet of the previous rtp stream with an "old" timestamp" was sent. 

== Remote PCAP stopped to capture in some situations ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141422 141422]
|}
E.g. if SIP/UDP Signaling traces were enabled remote PCAP stopped on large SIP packets because it was not possible to send larger buffers than 8k on stream sockets.

== SIP: T38 renegotiation failed with ICE ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141438 141438]
|}
ICE attributes got damaged in answer. 

== 'Idle Reset' via WEB UI or 'ireset' command must not reset before all log messages and CDRs are sent ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141482 141482]
|}


== IP38 : unable to detect Lebanon style busy tone ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141503 141503]
|}
Lebanon uses busy tone with 440Hz and 280/380ms cadence

== Application trap after many configuration changes ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141559 141559]
|}
After many configuration changes or active user switches the app could crash.

== SIP: Fixed handling of "Content-Type: application/ms-conf-invite+xml" ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141626 141626]
|}
Fixed handling of "Content-Type: application/ms-conf-invite+xml". Reject with "SIP/2.0 420 Bad Extension", instead of taking it as voice call without SDP offer. 

== A new call was not scrolled into view yet ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141646 141646]
|}
If a call control became visible it was not scrolled into view, i.e. a new incoming call or a new call initiated via R-key possibly appeared in the area that was scrolled off.

== SIP: SIP-IF fails to register if initial DNS query fails to resolve domain name ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141651 141651]
|}
SIP-IF fails to register if initial DNS query fails to resolve domain name. No retry of DNS. 

== Testlicenses with experation date still caused a 100h timeout if not extended ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141665 141665]
|}
The test licenses with experation date are supposed to work until that date. 

== SIP: Bad combination of public RTP address and private RTP port in SDP ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141688 141688]
|}
Bad combination of public RTP address and private RTP port in SDP, but only if config file option /ice-disabled was used and STUN server was configured at the SIP interface. 

== Gateway: Config option "Proposed Registration Interval" did not appear when "Register as Gateway" was selected ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141752 141752]
|}
Config option "Proposed Registration Interval" did not appear when "Register as Gateway" was selected. Related to SIP interfaces only. 

== Favourite List on Extension Module 2 has not been displayed ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141762 141762]
|}
Favourite List on Extension Module 2 has not been displayed 

== IP232/222/111: iQM Phone display features not working ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141767 141767]
|}
iQM information is not displayed on phone ui. 

== IP-DECT: Node support ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141777 141777]
|}
IP-DECT base stations support duplicate numbers with different nodes now.

== Possible memory leak with call list on CF cards ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141841 141841]
|}
There can be a memory leak if the call list is used on a CF card. 

== Box could trap during boot when there are plenty of licenses installed ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=141892 141892]
|}
Box could trap during boot when there are plenty of licenses installed. 

== IP222 IP232 IP241: First RTP packet sometimes has the wrong timestamp -2- ==

{|
|Status
|Assigned
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142042 142042]
|}
One packet of the previous rtp stream with an "old" timestamp" was sent. 

== SIP: STUN not always used to map RTP ports ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142047 142047]
|}
STUN not used to map RTP ports, if NAT type discovery failed. 

== NAT: NAT of ICMP packets did not work anymore ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142065 142065]
|}
NAT of ICMP packets did not work anymore. Wrong checksum calculated. 

== IP232: Could not cancel input on touch keyboard ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142146 142146]
|}
If touch-keyboard has been touched, the user can change the selected key by moving around, but the user could not cancel by moving outside touch-keyboard. No this works. 

== H.323: Potential trap on unusual call clearing ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142267 142267]
|}
An assertion because of duplicate RELEASE message from stack could happen. Circumstances under which this could happen unclear, but very rare. 

== Possible trap closing application sharing ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142325 142325]
|}
thread is waiting for a process to start. 

== IP232/222/111: Wake up LCD when received text message is displayed ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142340 142340]
|}
Wake up LCD when received text message is displayed. 

== PBX: OEM Registration licenses did not work anymore ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142371 142371]
|}
New handling of license versions broke the OEM licenses 

== PBX CDRs: Remote number in CDRs for diverted calls wrong in configuration with nodes ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142428 142428]
|}
As remote number the normalized number was used an not the relative 

== Gateway: Emergency calls did not work if no DSP channels were available ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142455 142455]
|}
Now a call is disconnected to free a DSP channel 

== Voicemail: Freeing resources for <store-get-msgcount> asap ==

{|
|Status
|Resolved
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142523 142523]
|}
Reducing memory footprint in large-scale installations 

== SIP: Trap when receiving SIP request ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142828 142828]
|}
Trap when receiving SIP request. 

== Improved usability on smartphones with small display ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142830 142830]
|}
Moved the headline into the scroll list in thoses cases where OK/Cancel buttons existed anyways, so the headline with the back button was not crucial and could scroll out and in the directory search where the headline was only text.

== SIP: PUBLISH to External UC did not work ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142841 142841]
|}
PUBLISH to External UC contains bad To-URI. 

== SIP: Use serial-no for registration instead of hw-id ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142845 142845]
|}
Format of serial no without '-'. If no user-id is specified for registration. E.g. "0090332f68cd" instead of "IP222-2f-68-cd" 

== PBX SOAP: Possible mixup with two simultaneous UserCall opertions ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142854 142854]
|}
It could happen, that the same outgoing call was actually indicated on both UserCall operations 

== IP222 IP232 IP241: First RTP packet sometimes has the wrong timestamp -3- ==

{|
|Status
|Assigned
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142857 142857]
|}
One packet of the previous rtp stream with an "old" timestamp" was sent. 

== PBX: Session Border Object does not need license anymore ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142861 142861]
|}
The PBX license SessionBorder is now obsolete 

== Call Lists on CF: Duplicate entries if call was sent to multiple registrations or mobility ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142904 142904]
|}
The record needs to marked as a duplicate 

== myPBX: "Start minimized" didn't work ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142925 142925]
|}
When the option "Show in taskbar" was disabled, the option "Start minimized" did not work. <-- ctiwin.cs -->

== SIP: Validate SIP Request-Line before go on parsing ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143002 143002]
|}
Validate SIP Request-Line before go on parsing. Ignore badly formated requests. 

== Phones: Cut off leading whitespace from dial string ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143006 143006]
|}
IP241/240/230/200/110 

== PBX: Registration without authentication possible even with TLS only flag set on device ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143205 143205]
|}
If the IP Filters for non-authenticated registration and 'No of Regs w/o Pwd.' allowed it, a registration without authentication was possible, even if TLS only was set. In case of TLS only, only TLS registrations with a matching and verified certificate should be allowed. 

== IP-DECT: Master trap ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143206 143206]
|}
There is a Master trap because of an uninitialized variable within a facility call. This is fixed now.

== PBX CDRs: Tranfered calls thru a Broadcast object were not shown correctly in CDRs from the Broadcast object ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143307 143307]
|}
The rel-to/from events were missing so reporting classified these as incomplete 

== Voicemail: Sending Connected Number Within H.323 CONNECT Message ==

{|
|Status
|Resolved
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143478 143478]
|}
The connected number as configured and with a numbering-plan=private 

= 11r1 Service Release 3 =
Changes included in Version 11r1 Service Release 3
[http://mantis.innovaphone.com/view.php?id=143586 Definition]

== Refresh myPBX call list if last call couldn't be found inside call list update ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=142923 142923]
|}
If a CDR isn't processed within the 2 second timeout of myPBX, the returning call list won't contain the last call.  

== SIP: Trap when call is terminated while inbound INVITE transaction is in progress ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143631 143631]
|}
Trap when call is terminated while inbound INVITE transaction is in progress. 

== PBX Session Border Object: All endpoints were deregistered when one Session Border object was modified ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143668 143668]
|}
This also cleared current calls 

== PBX: Execute CFB und Trunk/Gateway objects, if the far endpoint rejects call with busy ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143675 143675]
|}
This is useful to do re-routing in case of a called service is busy 

== SIP: UPDATE request was sent with wrong Session-Expires header ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143765 143765]
|}
UPDATE request was sent with wrong Session-Expires header. Value of refresher-param was wrong ("uac" instead of "uas"). 

== Sporadic click noise at the TDM interfaces and in the conference ==

{|
|Status
|Closed
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143817 143817]
|}
The last recent DSP code created sporadic click noise at the TDM interfaces (BRI and PRI) and during conferences on the IP6010.

== IP-DECT: Support for new IP1202 ==

{|
|Status
|Assigned
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143904 143904]
|}
Support for new IP1202 is added.

== WebRTC: Interoperability with Firefox 37.0.1 ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143652 143652]
|}
Firefox 37.0.1 requires a=rtpmap lines for all RTP payload types. Even for RTP payload types that are statically assigned by IANA. http://www.iana.org/assignments/rtp-parameters/rtp-parameters.txt 

== New config option "No ICE" for Gateway interfaces ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143730 143730]
|}
New config option "No ICE" for Gateway interfaces (VOIP_OPTION_NO_ICE) 

== IP222/111: Quick retrieve held call with left key ==

{|
|Status
|To-decide
|-
|Id
|[http://mantis.innovaphone.com/view.php?id=143823 143823]
|}
Quick retrieve held call with left key.

Reference10:Concept Exchange Calendar Connector

2012-11-12T15:23:48Z

MrOiso: /* innovaphone Linux Application Platform */

==Usage==

You can use the innovaphone Exchange Calendar Connector application to set the presence of a PBX user according to the Outlook calendar of the user. 
If the user has e.g. a meeting, the presence will be set to '''busy''' and the presence note to the subject of the calendar item (see [[ #Presence_Note_and_Activity | Presence Note and Activity]]).

==Requirements==

===innovaphone PBX===
The PBX must be V10 or higher.

===innovaphone Linux Application Platform===

It is needed to have the [[Reference9:Concept_Linux_Application_Platform|application platform]] installed and running with Hotfix13.

===Microsoft Exchange Server===

The innovaphone Exchange Calendar Connector application supports the Microsoft Exchange Server 2010 SP1 and SP2!

==Installation==

Download the latest version of innovaphone Exchange Calendar Connector.

Log into the application platform, go to the Applications tag, click on [[ Reference9:Concept_Linux_Application_Platform#Upload.2FUpdate|Upload/Update]] and upload the downloaded file.
The installation will start automatically and the page will refresh every two seconds showing the installation process.
If there is no error during the installation you will see at the end "Installation was succesfull". Otherwise,
you will get "installation failed" and the reason why it went wrong.

===Hotfix===
If you have already installed the latest version of the exchange application, simply download the Exchange...HotfixIncremental for your platform (VM or IPxx10) or if you have missed some hotfixes, download the Exchange...HotfixCumulative archive, which contains all hotfixes since hotfix1.
 
 
Upload this hotfix archive [[Reference9:Concept_Linux_Application_Platform#Upload.2FUpdate|here]].

==Configuration==
===Device===

The name (H323) of the PBX objects, whos calendars shall be monitored must match to a prefix of an email address of the configured domain. 
So the name must not contain white space or illegal email address characters.

e.g. the domain is '''innovaphone.com''' and the PBX user has the name '''test''', an exchange user with the email address '''test@innovaphone.com''' must exist!
e.g. the PBX user has the name '''Test Name''': this user can't be monitored, as its name contains a space.

The email address combined by name@domain doesn't need to be the primary SMTP address of the exchange user.

===PBX===

[[Image:exchange_pbx.jpg]]

* '''IP Address''': the IP address of your PBX
* '''Port''': the HTTP(s) port of your PBX
* '''Account''': the account, which reads the users from the PBX via SOAP
* '''Password''': password for the account
* '''Dyn-PBX-ID''': for a Dynamic PBX
* '''Domain''': the domain, e.g. '''innovaphone.com'''
* '''Calendar Note Language''': strings like '''Away''' and '''Free until''' are translated into this language
* '''Presence Update Interval''': the interval, in which the calender presence will be updated inside the pbx and PBX user objects are tracked
* '''HTTPS''': use HTTPS for the communication with the PBX
* '''Trace''': enable/disable tracing

===Exchange===

[[Image:exchange_ews.jpg]]

* '''Server''': the IP address or DNS name of your Microsoft Exchange Server
* '''Account''': the exchange user account, which has '''read access''' to the user calendars, which shall be monitored
* '''Password''': the password of the user
* '''Status Frequency''' (minutes): the subscriptions of user calendars are kept alive by dummy events, which are sent by the Exchange Server in this frequency
* '''Availability Timespan''' (hours): the timespan for which calendar items are retrieved
* '''Email(s)''': See [[ #Tentative_calendar_items | Tentative calendar items]]
* '''Exchange Version''': SP1 or SP2 of the Microsoft Exchange Server 2010

===Database===

The exchange application installs postgreSQL version 8.4 as database management system and creates the innovaphone-exchange database to store users from the PBX.
PostgreSQL is also available for other applications and any of them could create its own database.

====Password====

The exchange application creates the database user '''innovaphone-exchange''' with default password '''exchange'''.
This password may be changed at the innovaphone Exchange Calendar Connector page under Config/Database.

====Remote Access====

There are tools (PgAdmin III) that allow to connect to application databases remotely.
It is first needed to configure the IP you are connecting from under Config/Database at the innovaphone Exchange Calendar Connector page.

==Diagnostics==
===Logs===
Download/View logs of the innovaphone Exchange Calendar Connector application.

===Exchange Database===
====List users====
List all monitored users and their current subscription state.

====List calendar items====
List all retrieved calendar items.

==Backup and Restore==

You can both manually and automatically backup the database and configuration files for the exchange application under [[Reference9:Concept_Linux_Application_Platform#Backup|Administration/Backup]] in the application platform.

Configuration details for the update server can be found [[Reference9:Concept_Linux_Application_Platform#Backup|here]].

===Configuration Files===

'''saveinnovaphone-exchangecfgs''' is the command used to automatically save configuration files with the [[Reference9:Concept_Linux_Application_Platform#Command_File|Command File]].

===Data===

'''saveinnovaphone-exchangedb''' is the command to automatically backup the whole innovaphone Exchange Calendar Connector database with the [[Reference9:Concept_Linux_Application_Platform#Command_File|Command File]].

It is not needed to backup the exchange database, as the database is simply rebuilt after setting up a new configuration/system.

===Logs===

'''saveinnovaphone-exchangelogs''' to save log files with the [[Reference9:Concept_Linux_Application_Platform#Command_File|Command File]].

==Appendix==

===How it works===

* All users from the PBX are retrieved via SOAP
* The primary SMTP address inside the Microsoft Exchange Server is retrieved for all users with a '''valid''' h323 name
* A subscription for calendar events is established toward the Microsoft Exchange Server for all users with a primary SMTP address via SOAP [[ Reference9:Concept_Exchange#Microsoft_Exchange_Web_Services | EWS ]] with the configured user who has read access to the calendars of the other users
* The calendar items for the next e.g. 36 hours are retrieved for each new user (this step is only done once or if a new calendar event is received with the established subscription)
* The presence is set according to the calendar items of a user
* The established subscriptions monitor all changes inside the users calendars
* Each minute the PBX users are compared to the already existing ones and if needed added/removed/renamed etc.

The first time after you have successfully configured the PBX and the Exchange Server, all user subscriptions are established and all calendar items are retrieved.
This may take some minutes, according to the user count.

===Presence Note and Activity===

The settings of a calendar item determine the presence activity and note. 
A calendar item is ignored, if its '''busy type''' is '''free''' or '''tentative''' (see [[ #Tentative_calendar_items | Tentative calendar items]]). 
The subject of a calendar item is ignored, if the calendar item is '''private'''.

The activity is only set, if the calendar item has already started!
Otherwise just the note is set. If just the note is set, the merged presence, received by the PBX,
will prefer presences with an activity. If there is no presence with an activity, the note is shown e.g. on the phone/in myPBX.

====Tentative calendar items====

A tentative calendar item is neither free nor away, so it is ignored by default. 
But if the organizer of a calendar item is one of the configurable email addresses, the item is treated as away!

====Activity====
The activity is set accordingly to the busy type of a calendar item:

{| border=1
|| '''Calendar Item Busy Type''' || '''Presence Activity'''
|-
|| Free || ''ignored''
|-
|| Tentative || ''ignored'' or Away
|-
|| Busy || Busy
|-
|| Out of office || Away
|-
|}

====Note====
''The note of a not yet started calendar item contains the following parts:''

* the string '''Free until'''
* the date if the start date of the calendar item is not today
* the start time (Hours:Minutes) (if Hours:Minutes is '00:00', the time is cut and the date decreased by one day instead)
* the string '''Away''' if the activity is ''away''
* the subject of the calendar item or if the calendar item is private, the string '''Private'''

e.g.
Free until 28.07.2012 12:20 (Away: Vacation)
Free until 28.07.2012 12:20 (Meeting with boss)
Free until 12:20 (Away: Meeting with customer)
Free until 12:20 (Away: Private)

''The note of an already started calendar item:''

* the subject of the calendar item or if the calendar item is private, the string '''Private'''
* the string '''until'''
* the date if the end date of the calendar item is not today
* the end time (Hours:Minutes) (if Hours:Minutes is '00:00', the time is cut and the date decreased by one day instead)

===Microsoft Exchange Web Services===
For communication with the Microsoft Exchange Server, its [http://msdn.microsoft.com/en-us/library/exchange/bb204119%28v=exchg.140%29.aspx Exchange Web Services] are used.

===Installed Debian Packages===

The following packages (and their dependencies) are installed with innovaphone Reporting:

* php5-pgsql
* php5-mcrypt
* postgresql-8.4
* postgresql-common

===Configuration Files===

* pg_hba.conf is the client authentication configuration file and controls which hosts are allowed to connect, how clients are authenticated, which PostgreSQL user names they can use and which databases they can access.
* postgresql.conf is the PostgreSQL configuration file
* exchange.conf contains the PBX and Exchange Server configuration

===Data Files===

If you backup the innovaphone Exchange Calendar Connector database, you'll get a gz archiv, which contains the whole innovaphone-exchange database.

===Database Structure===

====users====

Users retrieved from the configured PBX.

====calendar_items====

Calendar items for the users retrieved from the Microsoft Exchange Server.

===Tools===

====NetDrive====

[http://www.heise.de/software/download/netdrive/55134 NetDrive] is a usefull webdav client, which can be used to access webdav of the innovaphone application platform.

====PGAdmin====

[http://www.pgadmin.org/ PGAdmin] is an administration tool for PostgreSQL databases.

====Putty====

[http://www.putty.org/ Putty] is SSH client to connect to the linux application platform.

==Known Problems==

[[Category:Concept|{{PAGENAME}}]]

Freeedit:Wiki Edit Sandbox

2010-01-06T21:18:04Z

MrOiso:

This is a dummy article to safely try editing wiki articles.

Tobias Gabriel - '''swisspro AG'''

= Wiki Syntax ([[Help:Formatting|more about formatting]], [[Help:Contents|generic help]]): =

Italic ''word'': <code>''word''</code> 
Bold '''word''': <code>'''word'''</code> 
:Indented line: <code>:line</code> 

# numbered list item: <code># list item</code>
## numbered list sub item: <code>## list item</code>

* dotted list item: <code>* list item</code>
** dotted list sub item: <code>** list item</code>

hidden search tag:  <code></code>

= Play Arena =

Marco Koch, '''Wrocklage Intermedia GmbH Germany''' 
Frank Schneebeck, '''ETe Datentechnik GmbH Germany''' 
Christoph Hanken, Paragon Data GmbH
Jonas Teckentrup, Paragon Data GmbH
Porretta Mauro, '''SARTE S.p.A. Italy''' 
Kevin Edmonds, '''Consult Partner GmbH''' 
Karsten Otto, '''westko network service GmbH''' 
Arne Stark, '''westko network service GmbH''' 
Henk Schuurman, '''Soft Solutions''' 
Marko Röhncke, '''Kevag-Telekom GmbH''' 
Kristijan Fabina, '''Datentechnik d.o.o.''' 
Dirk Lange, '''Nachrichtentechnik Bielefeld GmbH''' 
Ludwig Kempter, '''LEWTelNet GmbH''' 
Jukka Somiska, '''Daimler Finland''' 
Gisbert Cremerius, '''Hack-Attack''' 
Massimiliano Tamaro '''Test s.p.a Italy''' 
Marco Boschi '''Eksaip Vicenza''' 
Stig Aune, '''Stig Aune Consulting''' 
Sandro Haas, '''KufGem EDV GmbH''' 
Daniel Haidacher, '''KufGem EDV GmbH''' 
Marc Steiner, '''Inikon AG'''

Freeedit:Wiki Edit Sandbox

2010-01-06T21:17:55Z

MrOiso:

This is a dummy article to safely try editing wiki articles.

Tobias Gabriel - '''swisspro AG'''

= Wiki Syntax ([[Help:Formatting|more about formatting]], [[Help:Contents|generic help]]): =

Italic ''word'': <code>''word''</code> 
Bold '''word''': <code>'''word'''</code> 
:Indented line: <code>:line</code> 

# numbered list item: <code># list item</code>
## numbered list sub item: <code>## list item</code>

* dotted list item: <code>* list item</code>
** dotted list sub item: <code>** list item</code>

hidden search tag:  <code></code>

= Play Arena =

Marco Koch, '''Wrocklage Intermedia GmbH Germany''' 
Frank Schneebeck, '''ETe datentechnik GmbH Germany''' 
Christoph Hanken, Paragon Data GmbH
Jonas Teckentrup, Paragon Data GmbH
Porretta Mauro, '''SARTE S.p.A. Italy''' 
Kevin Edmonds, '''Consult Partner GmbH''' 
Karsten Otto, '''westko network service GmbH''' 
Arne Stark, '''westko network service GmbH''' 
Henk Schuurman, '''Soft Solutions''' 
Marko Röhncke, '''Kevag-Telekom GmbH''' 
Kristijan Fabina, '''Datentechnik d.o.o.''' 
Dirk Lange, '''Nachrichtentechnik Bielefeld GmbH''' 
Ludwig Kempter, '''LEWTelNet GmbH''' 
Jukka Somiska, '''Daimler Finland''' 
Gisbert Cremerius, '''Hack-Attack''' 
Massimiliano Tamaro '''Test s.p.a Italy''' 
Marco Boschi '''Eksaip Vicenza''' 
Stig Aune, '''Stig Aune Consulting''' 
Sandro Haas, '''KufGem EDV GmbH''' 
Daniel Haidacher, '''KufGem EDV GmbH''' 
Marc Steiner, '''Inikon AG'''

Freeedit:Wiki Edit Sandbox

2010-01-06T21:17:43Z

MrOiso:

This is a dummy article to safely try editing wiki articles.

Tobias Gabriel - '''swisspro AG'''

= Wiki Syntax ([[Help:Formatting|more about formatting]], [[Help:Contents|generic help]]): =

Italic ''word'': <code>''word''</code> 
Bold '''word''': <code>'''word'''</code> 
:Indented line: <code>:line</code> 

# numbered list item: <code># list item</code>
## numbered list sub item: <code>## list item</code>

* dotted list item: <code>* list item</code>
** dotted list sub item: <code>** list item</code>

hidden search tag:  <code></code>

= Play Arena =

Marco Koch, '''Wrocklage Intermedia GmbH Germany''' 
Frank Fschneebeck, '''ETe datentechnik GmbH Germany''' 
Christoph Hanken, Paragon Data GmbH
Jonas Teckentrup, Paragon Data GmbH
Porretta Mauro, '''SARTE S.p.A. Italy''' 
Kevin Edmonds, '''Consult Partner GmbH''' 
Karsten Otto, '''westko network service GmbH''' 
Arne Stark, '''westko network service GmbH''' 
Henk Schuurman, '''Soft Solutions''' 
Marko Röhncke, '''Kevag-Telekom GmbH''' 
Kristijan Fabina, '''Datentechnik d.o.o.''' 
Dirk Lange, '''Nachrichtentechnik Bielefeld GmbH''' 
Ludwig Kempter, '''LEWTelNet GmbH''' 
Jukka Somiska, '''Daimler Finland''' 
Gisbert Cremerius, '''Hack-Attack''' 
Massimiliano Tamaro '''Test s.p.a Italy''' 
Marco Boschi '''Eksaip Vicenza''' 
Stig Aune, '''Stig Aune Consulting''' 
Sandro Haas, '''KufGem EDV GmbH''' 
Daniel Haidacher, '''KufGem EDV GmbH''' 
Marc Steiner, '''Inikon AG'''

Howto:Control Call Forward with Voicemail XML Script

2009-03-12T19:53:32Z

MrOiso: /* Installation */

This article describes a custom voicemail XML script used to control call forward status (CFU only) via IVR from any phone for any user protected by a PIN.

==Applies To==
This information applies to

* innovaphone PBX, V7

==More Information==
The PBX Users are able to set call forward status from own phone only using IP Phone features or via DTMF Features available in the PBX. Anyway it is not possible to change the call forward from other phones or from external numbers. There a very nice wiki article about [[Howto:Control_Call_Forward_status_from_internal_and_external_phone|how to control call forward status from internal and external phones]], but its only available for predefined call forward profiles. The XML script appended to this article is used to switch call forward unconditional (CFU) on any user object to desired number from any phone able to call the VoiceMail object with [[Media:Follow me.zip|provided script]].

===Installation===
Extract the provided script to a CompactFlash card or HTTP-Server and create a VoiceMail object with URL pointed to FollowMe.xml.

For the first usage you must call the object from your own extension number and provide a PIN number. After that you will be able to set the CFU from any extension or external number.

===Known Problems===
The voice prompts are currently available only in German.

== Related Articles ==
[[Media:Follow me.zip|XML Script toControl Call Forward Status]]

[[Howto:How_to_Configure_the_innovaphone_Voicemail|How to Configure the innovaphone Voicemail]]

[[Howto:Control Call Forward status from internal and external phone]]

[[Category:Sample|{{PAGENAME}}]]