innovaphone wiki - User contributions [en]

Howto:Innovaphone Phones on FritzBox

2023-02-09T14:36:50Z

Tschweitzer: /* Configuration innovaphone User Config */

{{Template:3rd Party Input}}
==Applies To==
This information applies to

innovaphone IP Phones
User Configuration for registering on FritzBox



==More Information==

===Configuration FritzBox User===
Configure user within FritzBox-admin-menu as shown below.

Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) '''must not''' match or resemble the choosen username (Benutzername).
Although no error is displayed, later on phone login will just not work.

[[Image:Fritz1.PNG]]
[[Image:Fritz2.PNG]]

===Configuration innovaphone User Config===

Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232").

Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this:

[[Image:Innofritz.png]]

'''Attention !'''

Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722" as well the Protocol must be set to SIP/TCP.

===Configuration Message Waiting Key===
innovaphone phones support RFC 3842 which defines SIP based message waiting procedure.

This enables definition and use of message waiting function key and lamp to access FritzBox-built-in voicemail service.

By default, FritzBox-VM owns number **600. Any further described configuration assume this as default.
If this is changed by user or manufacturer, configuration below has to be adapted.

Control of MWI-LED and voicemail access via function key requires definition of both number '''and''' name as follows:
* Number: <FritzBox-VM>@fritz.box - default **600@fritz.box ; do NOT tick Append Own Number
* Name: <username>@fritz.box

[[Image:Innofritzmwi.png]]

===Voicemail on/off Key===
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3".

[[Image:Innofritz-on-off.png]]

===Known Problems===



[[Category:Howto|{{PAGENAME}}]]

Howto:Innovaphone Phones on FritzBox

2023-02-09T14:34:58Z

Tschweitzer: /* Configuration innovaphone User Config */

{{Template:3rd Party Input}}
==Applies To==
This information applies to

innovaphone IP Phones
User Configuration for registering on FritzBox



==More Information==

===Configuration FritzBox User===
Configure user within FritzBox-admin-menu as shown below.

Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) '''must not''' match or resemble the choosen username (Benutzername).
Although no error is displayed, later on phone login will just not work.

[[Image:Fritz1.PNG]]
[[Image:Fritz2.PNG]]

===Configuration innovaphone User Config===

Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232").

Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this:

[[Image:Innofritz.png]]

'''Attention !'''
Protocol must be SIP/TCP in FritzBox FW Version 7.50.

Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722"

===Configuration Message Waiting Key===
innovaphone phones support RFC 3842 which defines SIP based message waiting procedure.

This enables definition and use of message waiting function key and lamp to access FritzBox-built-in voicemail service.

By default, FritzBox-VM owns number **600. Any further described configuration assume this as default.
If this is changed by user or manufacturer, configuration below has to be adapted.

Control of MWI-LED and voicemail access via function key requires definition of both number '''and''' name as follows:
* Number: <FritzBox-VM>@fritz.box - default **600@fritz.box ; do NOT tick Append Own Number
* Name: <username>@fritz.box

[[Image:Innofritzmwi.png]]

===Voicemail on/off Key===
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3".

[[Image:Innofritz-on-off.png]]

===Known Problems===



[[Category:Howto|{{PAGENAME}}]]

Howto:Innovaphone Phones on FritzBox

2023-02-09T14:34:38Z

Tschweitzer: /* Configuration innovaphone User Config */

{{Template:3rd Party Input}}
==Applies To==
This information applies to

innovaphone IP Phones
User Configuration for registering on FritzBox



==More Information==

===Configuration FritzBox User===
Configure user within FritzBox-admin-menu as shown below.

Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) '''must not''' match or resemble the choosen username (Benutzername).
Although no error is displayed, later on phone login will just not work.

[[Image:Fritz1.PNG]]
[[Image:Fritz2.PNG]]

===Configuration innovaphone User Config===

Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232").

Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this:

[[Image:Innofritz.png]]

'''Attention !'''
Protocol must be SIP/TCP in FritzBox FW Version 7.50.
Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722"

===Configuration Message Waiting Key===
innovaphone phones support RFC 3842 which defines SIP based message waiting procedure.

This enables definition and use of message waiting function key and lamp to access FritzBox-built-in voicemail service.

By default, FritzBox-VM owns number **600. Any further described configuration assume this as default.
If this is changed by user or manufacturer, configuration below has to be adapted.

Control of MWI-LED and voicemail access via function key requires definition of both number '''and''' name as follows:
* Number: <FritzBox-VM>@fritz.box - default **600@fritz.box ; do NOT tick Append Own Number
* Name: <username>@fritz.box

[[Image:Innofritzmwi.png]]

===Voicemail on/off Key===
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3".

[[Image:Innofritz-on-off.png]]

===Known Problems===



[[Category:Howto|{{PAGENAME}}]]

Howto:Innovaphone Phones on FritzBox

2023-02-02T07:11:27Z

Tschweitzer: /* Configuration innovaphone User Config */

==Applies To==
This information applies to

innovaphone IP Phones
User Configuration for registering on FritzBox



==More Information==

===Configuration FritzBox User===
Configure user within FritzBox-admin-menu as shown below.

Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) '''must not''' match or resemble the choosen username (Benutzername).
Although no error is displayed, later on phone login will just not work.

[[Image:Fritz1.PNG]]
[[Image:Fritz2.PNG]]

===Configuration innovaphone User Config===

Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232").

Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this:

[[Image:Innofritz.png]]

'''Attention !'''
Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722"

===Configuration Message Waiting Key===
innovaphone phones support RFC 3842 which defines SIP based message waiting procedure.

This enables definition and use of message waiting function key and lamp to access FritzBox-built-in voicemail service.

By default, FritzBox-VM owns number **600. Any further described configuration assume this as default.
If this is changed by user or manufacturer, configuration below has to be adapted.

Control of MWI-LED and voicemail access via function key requires definition of both number '''and''' name as follows:
* Number: <FritzBox-VM>@fritz.box - default **600@fritz.box ; do NOT tick Append Own Number
* Name: <username>@fritz.box

[[Image:Innofritzmwi.png]]

===Voicemail on/off Key===
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3".

[[Image:Innofritz-on-off.png]]

===Known Problems===



[[Category:Howto|{{PAGENAME}}]]

Howto:Innovaphone Phones on FritzBox

2023-02-02T07:11:00Z

Tschweitzer: /* Configuration innovaphone User Config */

==Applies To==
This information applies to

innovaphone IP Phones
User Configuration for registering on FritzBox



==More Information==

===Configuration FritzBox User===
Configure user within FritzBox-admin-menu as shown below.

Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) '''must not''' match or resemble the choosen username (Benutzername).
Although no error is displayed, later on phone login will just not work.

[[Image:Fritz1.PNG]]
[[Image:Fritz2.PNG]]

===Configuration innovaphone User Config===

Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232").

Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this:

[[Image:Innofritz.png]]

'''Fetter Text'''Attention !'''Fetter Text'''
Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722"

===Configuration Message Waiting Key===
innovaphone phones support RFC 3842 which defines SIP based message waiting procedure.

This enables definition and use of message waiting function key and lamp to access FritzBox-built-in voicemail service.

By default, FritzBox-VM owns number **600. Any further described configuration assume this as default.
If this is changed by user or manufacturer, configuration below has to be adapted.

Control of MWI-LED and voicemail access via function key requires definition of both number '''and''' name as follows:
* Number: <FritzBox-VM>@fritz.box - default **600@fritz.box ; do NOT tick Append Own Number
* Name: <username>@fritz.box

[[Image:Innofritzmwi.png]]

===Voicemail on/off Key===
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3".

[[Image:Innofritz-on-off.png]]

===Known Problems===



[[Category:Howto|{{PAGENAME}}]]

Howto:Innovaphone Phones on FritzBox

2023-02-02T07:10:45Z

Tschweitzer: /* Configuration innovaphone User Config */

==Applies To==
This information applies to

innovaphone IP Phones
User Configuration for registering on FritzBox



==More Information==

===Configuration FritzBox User===
Configure user within FritzBox-admin-menu as shown below.

Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) '''must not''' match or resemble the choosen username (Benutzername).
Although no error is displayed, later on phone login will just not work.

[[Image:Fritz1.PNG]]
[[Image:Fritz2.PNG]]

===Configuration innovaphone User Config===

Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232").

Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this:

[[Image:Innofritz.png]]

'''Fetter Text'''Attention !
Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722"

===Configuration Message Waiting Key===
innovaphone phones support RFC 3842 which defines SIP based message waiting procedure.

This enables definition and use of message waiting function key and lamp to access FritzBox-built-in voicemail service.

By default, FritzBox-VM owns number **600. Any further described configuration assume this as default.
If this is changed by user or manufacturer, configuration below has to be adapted.

Control of MWI-LED and voicemail access via function key requires definition of both number '''and''' name as follows:
* Number: <FritzBox-VM>@fritz.box - default **600@fritz.box ; do NOT tick Append Own Number
* Name: <username>@fritz.box

[[Image:Innofritzmwi.png]]

===Voicemail on/off Key===
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3".

[[Image:Innofritz-on-off.png]]

===Known Problems===



[[Category:Howto|{{PAGENAME}}]]

Howto:Innovaphone Phones on FritzBox

2023-02-02T07:08:38Z

Tschweitzer: /* Configuration innovaphone User Config */

==Applies To==
This information applies to

innovaphone IP Phones
User Configuration for registering on FritzBox



==More Information==

===Configuration FritzBox User===
Configure user within FritzBox-admin-menu as shown below.

Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) '''must not''' match or resemble the choosen username (Benutzername).
Although no error is displayed, later on phone login will just not work.

[[Image:Fritz1.PNG]]
[[Image:Fritz2.PNG]]

===Configuration innovaphone User Config===

Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232").

Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this:

[[Image:Innofritz.png]]

Attention! Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722"

===Configuration Message Waiting Key===
innovaphone phones support RFC 3842 which defines SIP based message waiting procedure.

This enables definition and use of message waiting function key and lamp to access FritzBox-built-in voicemail service.

By default, FritzBox-VM owns number **600. Any further described configuration assume this as default.
If this is changed by user or manufacturer, configuration below has to be adapted.

Control of MWI-LED and voicemail access via function key requires definition of both number '''and''' name as follows:
* Number: <FritzBox-VM>@fritz.box - default **600@fritz.box ; do NOT tick Append Own Number
* Name: <username>@fritz.box

[[Image:Innofritzmwi.png]]

===Voicemail on/off Key===
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3".

[[Image:Innofritz-on-off.png]]

===Known Problems===



[[Category:Howto|{{PAGENAME}}]]