Howto:Sewan SIP Provider Compatibility Test
Innovaphone Compatibility Test Report
Summary
SIP Provider: Sewan (France)
- Features:
- Direct Dial In
- DTMF
- Supported Codecs by the provider
- G711
- G729
- T.38
The provider does not support all required innovaphone features and is therefore not qualified as recommended SIP Provider.
Current test state
The tests for this product could not be completed or not all mandatory tests were passed. See the Summary section for more details.
Testing of this product has been finalized September 16th, 2011.
Testing Enviroment
Scenario
This scenario describes a setup where the PBX and phones are in a private network. The provider supports NAT detection. As a result, the IP800 can work without a stun server.
Test Results
For more information on the test procedure, please read the following wiki article: SIP Interop Test Description. Bold lines in the test results indicate a KO-criteria.
Basic Call
Tested feature | Result |
---|---|
call using g711a | Yes |
call using g711u | Yes |
call using g723 | No |
call using g729 | Yes |
Overlapped sending | No |
early media channel | Yes |
Fax using T.38 | Yes |
CGPN can be suppressed | Yes |
CLIP no screening | Yes |
Reverse Media Negotiation | Yes |
Long time call possible | Yes |
External Transfer | Yes, requires MediaRelay |
NAT Detection | Yes |
Voice Quality OK? | Yes |
Direct Dial In
Tested feature | Result |
---|---|
Inbound(Provider -> Innovaphone) | Yes |
Outbound(Innovaphone -> Provider) | No, CGPN number is displayed only as anonym |
DTMF
Tested feature | Result |
---|---|
DTMF tones sent correctly | Yes |
DTMF tones sent correctly via SIP-Info | Yes |
DTMF tones received correctly | Yes |
Hold/Retrieve
Tested feature | Result |
---|---|
Call can be put on hold | Yes |
Held end hears music on hold / announcement from PBX | Yes, but with audible distortion. Requires MR and exclusive coder. |
Held end hears music on hold / announcement from provider | Yes |
Transfer with consultation
Tested feature | Result |
---|---|
Call can be transferred | Yes |
Held end hears music on hold | Yes |
Call returns to transferring device if the third Endpoint is not available | Yes |
Transfer with consultation (alerting only)
Tested feature | Result |
---|---|
Call can be transferred | Yes |
Held end hears music on hold or dialling tone | Yes |
Call returns to transferring device if the third Endpoint is not available | Yes |
Blind Transfer
Tested feature | Result |
---|---|
Call can be transferred | Yes |
Held end hears dialling tone | Yes |
Broadcast Group & Waiting Queue
Tested feature | Result |
---|---|
Caller can make a call to a Broadcast Group | Yes |
Caller can make a call to a Waiting Queue | Yes |
Announcement if nobody picks up the call | Yes |
Configuration
General Information
Firmware version
- IP800: 9.00 hotfix1
- IP22: 8.00 hotfix16 - build 805005400
- IP200: 9.00 hotfix1
- IP230: 9.00 hotfix1
SIP - Trunk
First of all the SIP Trunk must be configured. Make sure that Media Relay is activated.
Number Mapping
The complicated part on this issue is the correct mapping of the outgoing and incoming numbers.
Route Settings
Because Sewan, as most SIP - Providers too, doesn't support overlap sending, you must enable the blockwise sending of the phone number. You can do this by enabling Force enblock in the automatically generated Routes.
The second setting you must check is Interworking(QSIG,SIP). This feature must be enabled to properly relay supplementary services, like Hold over the SIP Trunk. If this checkbox is unchecked only basic call Information like connect and disconnect will be forwarded by the Gateway.
Fax
The FAX was connected via a IP22 to the IP800. When configuring the IP22 you must keep in mind that you will use the analog interface for fax communication. That's why the T.38 codec must be enabled.
CLIR
To suppress the CGPN for outbound calls a config line option must be activated. Please enter the following lines in your browser:
http://PBX-IP-address/!config add SIP /pai http://PBX-IP-address/!config write http://PBX-IP-address/!config activate