From innovaphone-wiki

Jump to: navigation, search
There are other versions of this article: Reference | Reference9 (this version) | Reference10 | Reference11r1

The physical settings of the analogue FXS interfaces can be made here:

Pulse: A checked check box enables the recognition of pulse dialling on the relevant interface.
Reverse: A checked check box inverts the wiring of the relevant interface. This is only necessary in the event of incompatibility of the terminals, since some terminals (for example, in the US) are wired the opposite way.
First ring followed by CLIP: This checkbox creates a short ring pulse of 160ms duration followed by a pause of 1 second. This pause is then used to send CLIP information to the phone. Then the ringing switches over to the normal intervals depending on the call being internal or external. If not checked the ringing directly starts with the corrosponding interval.
Some telephones can explicitly suppress the first ring just to receive and present CLIP before audible ringing (often called Ring OFF in menues). If a telephone cannot suppress the first ring or is not configured to do so, this checkbox may be unchecked to immediately start ringing without a short audible ring, which will occur otherwise.
Telephones that do not accept CLIP information after the second ring need this checkbox checked to present CLIP correctly. One known model is the T-COM Concept P412.
Receive gain: Set the loudness a user receives at this interface. Default is -10dB for short lines and -7 dB for long lines.
Transmit gain: Set the loudness a user transmits at this interface. Default is -3dB for short lines and 0 dB for long lines. Some fax devices may need a lower transmit level to avoid clipping.
Country: Set the line impedance for different countries. In Europe CTR21 is used.
Internal/External call distinction: Normally internal and external calls are distinguished by terms of different rythms of the ringing voltage. Normally external calls use 1sec ringing voltage - 4sec pause. Internal calls normally use 375ms ringing voltage - 250ms pause - 375ms ringing voltage - 4sec pause. Select swiss to assign this rythms the opposite way. You can also select one rythm to be used permanently, no matter if the calls are external or internal.
Metering pulse frequency: possible values : 16kHz or 12kHz.
16kHz is common for most countries. Austria and Swiss use 12kHz.
Optimization grade: As per default the TEL ports are optimized for low power consumption (Optimization 'high' and 'mid'). This decreases the usual on-hook supply voltage of 48V down to 24V. Most conventional phones and faxes can deal with this. In case a special phone is connected that cannot deal with this low voltage or if a long cable is used this dropdown can be modified.
'high' and 'mid' both set 24V on-hook voltage. The off-hook loop current is set to 20mA.
'low' sets 48V on-hook-voltage. The off-hook loop current is now configurable in three steps :
The output voltage of an IP28 port can’t be changed. It’s fix to 35 V.
Loop Current: As described before this topic changes the off-hook loop current and can be modified if 'Optimization grade' is set to 'low'.
'low' sets 20mA, 'mid' set 23mA, 'high' sets 26mA. Specific gateways may offer additional higher values.
RingTrip Threshold: This topic modifies the current-threshold which lets the gateway distinguish between a ringing condition and a hook-off condition while the ringing voltage is applied from the gateway to the phone. Crossing this threshold by the phone, the gateway assumes a hook-off and therefore stops applying the ringing voltage and enters normal off-hook state. Imagine you encounter a problem that looks like this : very short time ringing, somehow immediate off-hook and then on-hook transition again - this call is lost. This looks like your phone requires too much current for ringing that makes the gateway wrongly assume a hook-off. In this case it is recommended to try the higher threshold currents.
'low' sets 34mA, 'mid' sets 37,5mA and 'high' sets 40mA.
Ringing Voltage This topic modifies the ringing voltage used for ringing. Ringing frequency is 25Hz.
'low' sets 65Vpk/45Vrms, 'mid' sets 68Vpk/48Vrms and 'high' sets 70Vpk/49,5Vrms AC.

Some considerations about Flash, R and Dial-pulses

The a/b ports support further signaling through Flash-key (other sources call it R-key, what means exactly the same) followed by DTMF-Key combinations. For example, pressing Flash while already having a peer connection will set the current connection into call-hold state (the peer side hears Music-On-Hold) and establish a new call.

From a technical point of view Flash is a short interruption in offhook loop-current. You can imagine Flash as a very short hook-on/hook-off event. The on-hook duration of a Flash event is normally between 100ms and 300ms. Shorter durations are regarded as dial-pulses (if enabled), longer durations are regarded as seperate hook-on and hook-off events. If you encounter difficulties regarding Flash, be sure you have configured a flash-time between 100ms and 300ms in your phone.

Dial-pulses are also short interruptions of the offhook loop-current and can also be imagined as short hook-on/hook-off events. The only difference to Flash is, Dial-pulses have a much shorter duration of 40ms to 80ms.
Several successive Dial-pulses form a digit of a number. The pulses of one digit are seperated by a pause of about 60-80ms. Different digits are seperated with pauses that are much longer (at least 80ms, but can be much more). The digit '1' consists of one single pulse, '2' is two successive pulses and so on, '0' is ten successive pulses.

Pinout of the a/b connector IP29-2, IP29-4, IP29, IP38


Pin Function

Pinout of the a/b connector IP29-20


Pin Function
Personal tools