Reference13r1:Concept IP29-20: Difference between revisions
Line 85: | Line 85: | ||
Next to own assembling, | Next to own assembling, below listed are some 3rd-party-products (information is subject ot change): | ||
* [http://www.logilink.org/Produkte_LogiLink/Passive_Netzwerkkomponenten/Telefonzubehoer/Modular_Adapter-4-Port.htm?seticlanguage=en LogiLink-Adapter] | * [http://www.logilink.org/Produkte_LogiLink/Passive_Netzwerkkomponenten/Telefonzubehoer/Modular_Adapter-4-Port.htm?seticlanguage=en LogiLink-Adapter] | ||
* [https://www.l-com.com/ethernet-tia568b-splitter-8x8-plug-4-6x2-jacks L-Com-Adapter] | * [https://www.l-com.com/ethernet-tia568b-splitter-8x8-plug-4-6x2-jacks L-Com-Adapter] |
Revision as of 09:01, 11 May 2020
Applies To
This information applies to
- innovaphone IP29-20
Overview
innovaphone IP29-20 is an IP adapter for twenty analogue interfaces (FXS).
It includes 20 interface licenses upon delivery.
Requirements
- Firmware 13r1sr11
- innovaphone PBX with appropriate amount of Port<v> Licenses
- Power over Ethernet+ supply according to IEEE 802.3at, Class 4 (PoE+)
- appropriate adapter cable - see below
Configuration
Connection
As different cabling concepts might be applied, innovaphone does not deliver any connection cables with the system.
Note: Below mentioned 3rd-pty-products are subject to change and there might be alternative products of other manufacturers/resellers.
Find below a list of possible connection concepts and their realisation:
PinOUT
Built-in 8P8C connectors provide following pinout:
Pin | Function |
1 | RING-2 |
2 | TIP-2 |
3 | RING-3 |
4 | TIP-1 |
5 | RING-1 |
6 | TIP-3 |
7 | RING-4 |
8 | TIP-4 |
This pinout is especially designed for use with twisted-pair Ethernet patch cables
Direct terminal connection
In case of direct connection of analogue terminals by use of 2-wire-a/b-connectors RJ-11 / modular jack 6P2C, a special adapter has to be used.
This adapter has to distribute above mentioned IP29-20 pinout to four 6P2C connectors using the pinout below:
Pin | Function |
3 | TIP |
4 | RING |
Next to own assembling, below listed are some 3rd-party-products (information is subject ot change):
Patch-panel based connection
In case of patch-panel based connection, used adapter cable depends on used patch panel:
- patch-panel with 8-wire-connectors (8P8C): use twisted-pair Ethernet patch cables
- patch-panel with 2-wire-connectors (8P2C): use of an adapter cable splitting up 8P8C to 4 x 8P2C.
- For the 2nd option, we know about this 3rd-party-product.
Provisioning
IP29-20 is added to an existing V13-PBX-system by execution of V13-installer upon initial device startup.
Analogue extensions connected to IP29-20 are bound to the innovaphone PBX by use of the V13-device-provisioning.
If an appropriate number of Port<v> licenses is available in the corresponding innovaphone PBX,
the registration of analogue terminals to the selected users takes place immediately after the provisioning is confirmed.
Restrictions
- In case of Class3-PoE power supply (no PoE+), the first eight FXS interfaces (1-8) are available within the device.