Howto:Adjust Speaker volume on IP241 IP222 IP232: Difference between revisions
m (→Summary) |
|||
| Line 14: | Line 14: | ||
<nowiki>http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume 2</nowiki> | <nowiki>http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume 2</nowiki> | ||
http://ip-adress-of-the-phone/!config activate | <nowiki>http://ip-adress-of-the-phone/!config activate</nowiki> | ||
Example to turn up the speaker volume a bit more: | Example to turn up the speaker volume a bit more: | ||
http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume 4 | <nowiki>http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume 4</nowiki> | ||
http://ip-adress-of-the-phone/!config activate | <nowiki>http://ip-adress-of-the-phone/!config activate</nowiki> | ||
'''To avoid hearing damage, please be careful with the values!''' Increase the values step by step. You hear the difference after the !config activate | '''To avoid hearing damage, please be careful with the values!''' Increase the values step by step. You hear the difference after the !config activate | ||
--> a value of /spk-volume 2 (db) means a boost of 26%, a value of 6 a boost of 100%, a value of 10 a boost 1000%! | |||
Example to turn down the speaker volume a bit: | Example to turn down the speaker volume a bit: | ||
http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume -2 | <nowiki>http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume -2</nowiki> | ||
http://ip-adress-of-the-phone/!config activate | <nowiki>http://ip-adress-of-the-phone/!config activate</nowiki> | ||
Example to restore default behaviour: | Example to restore default behaviour: | ||
http://ip-adress-of-the-phone/!config rem AC-DSP0 HEADSET /spk-volume | <nowiki>http://ip-adress-of-the-phone/!config rem AC-DSP0 HEADSET /spk-volume </nowiki> | ||
http://ip-adress-of-the-phone/!config activate | <nowiki>http://ip-adress-of-the-phone/!config activate</nowiki> | ||
If you satisfied with the settings, type: | If you satisfied with the settings, type: | ||
http://ip-adress-of-the-phone/!config write | <nowiki>http://ip-adress-of-the-phone/!config write</nowiki> | ||
Now, the values are in the config. | Now, the values are in the config. | ||
Revision as of 14:46, 25 October 2013
Applies To
DHSG and USB Headsets on IP241, IP222, IP232 with V9 and above
Problem
Headsets from different manufacturer respond different (too loud or too quiet) on the default volume setting at the USB or DHSG Ports.
Summary
It's possible to turn down or turn up the volume individual within the phone configuration. The values are offsets, which means that 0 ist not off, it's the default value of the firmware.
You can set the speaker volume /spk-volume and the microphone volume /mic-volume. Normaly the headsets microphone volume must not be changed, because the user adapts the loudness of his own voice from situation to situation. The common problem is the speaker volume.
Example to turn up the speaker volume a bit:
http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume 2 http://ip-adress-of-the-phone/!config activate
Example to turn up the speaker volume a bit more:
http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume 4 http://ip-adress-of-the-phone/!config activate
To avoid hearing damage, please be careful with the values! Increase the values step by step. You hear the difference after the !config activate
--> a value of /spk-volume 2 (db) means a boost of 26%, a value of 6 a boost of 100%, a value of 10 a boost 1000%!
Example to turn down the speaker volume a bit:
http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume -2 http://ip-adress-of-the-phone/!config activate
Example to restore default behaviour:
http://ip-adress-of-the-phone/!config rem AC-DSP0 HEADSET /spk-volume http://ip-adress-of-the-phone/!config activate
If you satisfied with the settings, type:
http://ip-adress-of-the-phone/!config write
Now, the values are in the config.
Please also note, that it's possible for future DSP code updates, that the default value can be changed (what means that "0" can be louder or quieter) and it's possible that updates of the headset manufacturer can change the volume, too.
In this case it's necessary to do the steps again.