Howto:Adjusting volume parameters on IP111 and IP112: Difference between revisions
No edit summary |
No edit summary |
||
| Line 4: | Line 4: | ||
==Problem== | ==Problem== | ||
* Customer may need control over the microphone sensitivity | * Customer may need control over the microphone sensitivity to lower background noise pickup | ||
* Customer may need higher speaker volume of handset, loudspeaker than configurable on the phone | * Customer may need higher speaker volume of handset, loudspeaker than configurable on the phone | ||
| Line 13: | Line 13: | ||
<nowiki>http://ip-adress-of-the-phone/!config activate</nowiki> | <nowiki>http://ip-adress-of-the-phone/!config activate</nowiki> | ||
Presently 21 is the default. Decreasing the value by 4 decreases the | Presently 21 is the default. Decreasing the value by 4 decreases the sensitivity by 6 dB. The allowed range of the ADC_Gain parameter is 0..31. The same command can be applied for speakerphone mode with name SPEAKER instead of HANDSET. | ||
Revision as of 11:35, 9 April 2015
Applies To
- IP111 with V11r1 and above
Problem
- Customer may need control over the microphone sensitivity to lower background noise pickup
- Customer may need higher speaker volume of handset, loudspeaker than configurable on the phone
Summary
The microphone sensitivity of the handset can be controlled with a sequence of commands along the lines
http://ip-adress-of-the-phone/!config add AC-DSP0 HANDSET /ADC_Gain 21 http://ip-adress-of-the-phone/!config activate
Presently 21 is the default. Decreasing the value by 4 decreases the sensitivity by 6 dB. The allowed range of the ADC_Gain parameter is 0..31. The same command can be applied for speakerphone mode with name SPEAKER instead of HANDSET.
It's possible to turn down or turn up the volume individual within the phone configuration. The values are offsets, which means that 0 is not off, it's the default value of the firmware.
The headset volume can be adjusted with http://addr/dsp.xml -> Volume
The other levels can be adjusted on the command line, the level is specified in db.
config add AC-DSP0 HANDSET /mic-volume config add AC-DSP0 HANDSET /spk-volume config add AC-DSP0 SPEAKER /mic-volume config add AC-DSP0 SPEAKER /spk-volume config add AC-DSP0 HEADSET /mic-volume config add AC-DSP0 HEADSET /spk-volume
The default is restored by a corresponding
config rem AC-DSP0 ...
command.
You can set the speaker volume /spk-volume and the microphone volume /mic-volume. Normally the headsets microphone volume must not be changed, because the user adapts the loudness of his own voice from situation to situation. The common problem is the speaker volume.
Example to turn up the speaker volume a bit:
http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume 2 http://ip-adress-of-the-phone/!config activate
Example to turn up the speaker volume a bit more:
http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume 4 http://ip-adress-of-the-phone/!config activate
To avoid hearing damage, please be careful with the values! Increase the values step by step. You hear the difference after the !config activate
The values are between -32 and +32, out of range values will be converted to the higher limit.
Example to turn down the speaker volume a bit:
http://ip-adress-of-the-phone/!config add AC-DSP0 HEADSET /spk-volume -2 http://ip-adress-of-the-phone/!config activate
Example to restore default behaviour:
http://ip-adress-of-the-phone/!config rem AC-DSP0 HEADSET /spk-volume http://ip-adress-of-the-phone/!config activate
If you satisfied with the settings, type:
http://ip-adress-of-the-phone/!config write
Now, the values are in the config.
Please also note, that it's possible for future DSP code updates, that the default value can be changed (what means that "0" can be louder or quieter) and it's possible that updates of the headset manufacturer can change the volume, too. So after doing a firmware update on the phone or on the headset, it's necessary to do the steps above again.