Howto:HFO NGN Connect - HFO - SIP Provider: Difference between revisions

From innovaphone wiki
Jump to navigation Jump to search
mNo edit summary
Line 1: Line 1:
'''Innovaphone Compatibility Test Report'''
'''Innovaphone Compatibility Test Report'''
== Summary ==
'''SIP Provider: HFO'''
<!--
The provider supports all required innovaphone features and is therefore qualified as [[Howto:What_is_a_%22recommended_product%22%3F#SIP_Provider|recommended SIP Provider]].
...
That being said, the provider has achieved x% of all possible test points. For more information on the test rating, please refer to [[Howto:SIP_Interop_Test_Description#|Test Description]]
Mention all important tests that were not passed in the summary.
E.g. in case that the provider doesn't support Reverse Media-Negotiation, mention in the summary that media relay and an exclusive coder setting must be configured:
Since the provider doesn't support Reverse Media negotiation, media relay and an exclusive coder setting must be configured. Opposed to a SIP trunk not needing Media-Relay, the transport of all RTP packets by the gateway will result in a higher CPU load for a call. As a result, the amount of concurrent calls is considerably lower compared to a SIP-Provider that doesn't require Media-Relay.
-->
* Features:
** Direct Dial In
** Fax over IP (T.38)
** DTMF
* Supported Codecs by the provider
** G711
** G729
** G723
** G726
** T.38 UDP
== Current test state ==
<!--{{Template:Compat Status "planned"}} -->
{{Template:Compat Status "in progress"}}
<!-- {{Template:Compat_Status_"referral_prod."|certificate=Tpl_sip.business_Toplink_SIP_Provider_-_product-cert.pdf}} -->
<!-- {{Template:Compat_Status_"engineered_prod."|certificate=Tpl_sip.business_Toplink_SIP_Provider_-_product-cert.pdf}} -->
<!-- {{Template:Compat_Status_"rec._prod."|certificate=Tpl_sip.business_Toplink_SIP_Provider_-_product-cert.pdf}} -->
<!-- {{Template:Compat Status "tested"(sip provider)}} -->
<!-- {{Template:Compat Status "rejected"}} -->
<!-- {{Template:Compat_Status_"referral_prod."-no-certificate}} -->
<!-- Testing of this product has been finalized January 1st, 1970. -->
<internal>
Beim Abschluss des Tests (egal ob gut, schlecht oder abgebrochen) <strong>bitte Nachricht an ckl</strong>!
</internal>
== Testing Enviroment ==
[[Image:SIPProviderTestTopology1.PNG]]
This scenario describes a setup where the PBX and phones are in a private network.
There are 3 major configuration variants of the SIP trunk, which one is used depends on the test results. The variants are:
* the SIP trunk is configured without Media Relay and without exclusive coder. This is the case if all tests were successful
* the SIP trunk is configured with Media Relay and STUN but without exclusive coder. This is the case when the test for "NAT Traversal" fails
* the SIP trunk is configured with Media Relay and exclusive coder. This is the case when the test for "Reverse Media Negotiation" fails
The test scenario should describe which SIP trunk configuration is needed.
== Test Results ==
For more information on the test procedure, please read the following wiki article: [[Howto:SIP_Interop_Test_Description|SIP Interop Test Description]]. Bold lines in the test results indicate a KO-criteria.
{{FIXME|reason=Note: Possible test results are Ok, Nok, Not tested, N/A(not available). Ok, Nok, N/A are self explanatory. "Not tested" is more a temporary note - if its still in the test after finishing, then the summary should explain why the feature was not tested. Remove this note in the final report}}
=== Basic Call ===
{| border="1"
!Tested feature
!Result
|----
|SIP over TLS(SIPS)
|Nok
|----
|SIP over TCP
|Nok
|----
|SRTP
|Nok
|----
|'''call using g711a'''
|'''Ok'''
|----
|'''call using g711u'''
|'''Ok'''
|----
|call using g729
|Nok
|----
|call using g722
|Ok
|----
|Overlapped sending
|Nok
|----
|'''early media channel'''
|'''Ok'''
|----
|Fax using T.38
|Ok
|----
|T.38 Transcoding by the provider
|
|----
|Reverse Media Negotiation
|Ok
|----
|CGPN can be suppressed
|Ok
|----
|CLIP no screening
|Ok
|----
|'''Long time call possible(>30 min)'''
|
|----
|'''External Transfer'''
|
|----
|NAT Detection
|Nok
|----
|Redundancy
|
|----
|'''Voice Quality OK?'''
|'''Ok'''
|}
=== Direct Dial In ===
{| border="1"
!Tested feature
!Result
|----
|'''Inbound(Provider -> Innovaphone)'''
|'''Ok'''
|----
|'''Outbound(Innovaphone -> Provider)'''
|'''Ok'''
|----
|'''Loop In call(Innovaphone -> Provider -> Innovaphone)'''
|'''Ok'''
|}
=== DTMF ===
{| border="1"
!Tested feature
!Result
|----
|'''DTMF tones sent correctly via RTP-events(RFC 2833)'''
|'''Ok'''
|----
|DTMF tones sent correctly via SIP-Info
|Nok
|----
|'''DTMF tones received correctly via RTP-events(RFC 2833)'''
|'''Ok'''
|}
=== Hold/Retrieve ===
{| border="1"
!Tested feature
!Result
|----
|'''Call can be put on hold'''
|'''Ok'''
|----
|Held end hears music on hold / announcement from PBX
|Ok
|}
=== Transfer with consultation ===
{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|
|----
|Held end hears music on hold
|
|}
The following tests are made to test if call transfer is working.
{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|Ok
|Ok
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|Ok
|Ok
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|Ok
|Ok
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|Ok
|Ok
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|Ok
|Ok
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|Ok
|Ok
|}
=== Transfer with consultation (alerting only) ===
{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred'''
|
|----
|Held end hears music on hold or dialling tone
|
|----
|'''Call returns to transferring device if the third'''
'''Endpoint is not available'''
|
|}
The following tests are made to test if call transfer is working.
{| border="1"
!Tested feature
!Voice Ok?
!MoH Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|
|
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|
|
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|
|
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|
|
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|
|
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|
|
|}
=== Blind Transfer ===
{| border="1"
!Tested feature
!Result
|----
|Call can be transferred
|
|----
|Held end hears dialling tone
|
|}
The following tests are made to test if call transfer is working.
{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|
|----
|inno1 calls PSTN-phone. inno1 transfers to inno2.
|
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|
|----
|PSTN-phone calls inno1. PSTN-phone transfers to inno2.
|
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|
|}
=== CFU / CFB Transfer ===
{| border="1"
!Tested feature
!Result
|----
|'''Call can be forward'''
|
|----
|'''Held end hears dialling tone'''
|
|}
=== CFNR / Blind Transfer (alerting only)===
{| border="1"
!Tested feature
!Result
|----
|'''Call can be transferred or forward'''
|
|----
|'''Held end hears dialling tone'''
|
|}
The following tests are made to test if call transfer is working.
{| border="1"
!Tested feature
!Voice Ok?
|----
|inno1 calls inno2. inno2 transfers to PSTN-phone.
|
|----
|inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
|
|----
|PSTN-phone calls inno1. inno1 transfers to inno2.
|
|----
|PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.
|
|}
=== Broadcast Group & Waiting Queue ===
{| border="1"
!Tested feature
!Result
|----
|'''Caller can make a call to a Broadcast Group'''
|
|----
|'''Caller can make a call to a Waiting Queue'''
|
|----
|'''Announcement if nobody picks up the call'''
|
|}
== Configuration ==
===Firmware version===
All innovaphone devices use Vx build xx-xxxxx as firmware.
=== SIP - Trunk ===
=== Number Mapping ===
=== Route Settings ===
=== Media Relay ===
=== Fax ===
[[Category:Compat|{{PAGENAME}}]]
'''Innovaphone Compatibility Test Report-old-test'''


== Summary ==
== Summary ==

Revision as of 10:47, 12 June 2015

Innovaphone Compatibility Test Report

Summary

SIP Provider: HFO

  • Features:
    • Direct Dial In
    • Fax over IP (T.38)
    • DTMF
  • Supported Codecs by the provider
    • G711
    • G729
    • G723
    • G726
    • T.38 UDP

Current test state

This product is being tested right now. The test is not yet completed.


<internal> Beim Abschluss des Tests (egal ob gut, schlecht oder abgebrochen) bitte Nachricht an ckl! </internal>

Testing Enviroment

SIPProviderTestTopology1.PNG

This scenario describes a setup where the PBX and phones are in a private network.

There are 3 major configuration variants of the SIP trunk, which one is used depends on the test results. The variants are:

  • the SIP trunk is configured without Media Relay and without exclusive coder. This is the case if all tests were successful
  • the SIP trunk is configured with Media Relay and STUN but without exclusive coder. This is the case when the test for "NAT Traversal" fails
  • the SIP trunk is configured with Media Relay and exclusive coder. This is the case when the test for "Reverse Media Negotiation" fails

The test scenario should describe which SIP trunk configuration is needed.

Test Results

For more information on the test procedure, please read the following wiki article: SIP Interop Test Description. Bold lines in the test results indicate a KO-criteria.

Tools clipart.png FIXME: Note: Possible test results are Ok, Nok, Not tested, N/A(not available). Ok, Nok, N/A are self explanatory. "Not tested" is more a temporary note - if its still in the test after finishing, then the summary should explain why the feature was not tested. Remove this note in the final report

Basic Call

Tested feature Result
SIP over TLS(SIPS) Nok
SIP over TCP Nok
SRTP Nok
call using g711a Ok
call using g711u Ok
call using g729 Nok
call using g722 Ok
Overlapped sending Nok
early media channel Ok
Fax using T.38 Ok
T.38 Transcoding by the provider
Reverse Media Negotiation Ok
CGPN can be suppressed Ok
CLIP no screening Ok
Long time call possible(>30 min)
External Transfer
NAT Detection Nok
Redundancy
Voice Quality OK? Ok

Direct Dial In

Tested feature Result
Inbound(Provider -> Innovaphone) Ok
Outbound(Innovaphone -> Provider) Ok
Loop In call(Innovaphone -> Provider -> Innovaphone) Ok

DTMF

Tested feature Result
DTMF tones sent correctly via RTP-events(RFC 2833) Ok
DTMF tones sent correctly via SIP-Info Nok
DTMF tones received correctly via RTP-events(RFC 2833) Ok

Hold/Retrieve

Tested feature Result
Call can be put on hold Ok
Held end hears music on hold / announcement from PBX Ok

Transfer with consultation

Tested feature Result
Call can be transferred
Held end hears music on hold

The following tests are made to test if call transfer is working.

Tested feature Voice Ok? MoH Ok?
inno1 calls inno2. inno2 transfers to PSTN-phone. Ok Ok
inno1 calls PSTN-phone. inno1 transfers to inno2. Ok Ok
inno1 calls PSTN-phone. PSTN-phone transfers to inno2. Ok Ok
PSTN-phone calls inno1. inno1 transfers to inno2. Ok Ok
PSTN-phone calls inno1. PSTN-phone transfers to inno2. Ok Ok
PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2. Ok Ok

Transfer with consultation (alerting only)

Tested feature Result
Call can be transferred
Held end hears music on hold or dialling tone
Call returns to transferring device if the third

Endpoint is not available

The following tests are made to test if call transfer is working.

Tested feature Voice Ok? MoH Ok?
inno1 calls inno2. inno2 transfers to PSTN-phone.
inno1 calls PSTN-phone. inno1 transfers to inno2.
inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
PSTN-phone calls inno1. inno1 transfers to inno2.
PSTN-phone calls inno1. PSTN-phone transfers to inno2.
PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.

Blind Transfer

Tested feature Result
Call can be transferred
Held end hears dialling tone

The following tests are made to test if call transfer is working.

Tested feature Voice Ok?
inno1 calls inno2. inno2 transfers to PSTN-phone.
inno1 calls PSTN-phone. inno1 transfers to inno2.
inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
PSTN-phone calls inno1. inno1 transfers to inno2.
PSTN-phone calls inno1. PSTN-phone transfers to inno2.
PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.

CFU / CFB Transfer

Tested feature Result
Call can be forward
Held end hears dialling tone

CFNR / Blind Transfer (alerting only)

Tested feature Result
Call can be transferred or forward
Held end hears dialling tone

The following tests are made to test if call transfer is working.

Tested feature Voice Ok?
inno1 calls inno2. inno2 transfers to PSTN-phone.
inno1 calls PSTN-phone. PSTN-phone transfers to inno2.
PSTN-phone calls inno1. inno1 transfers to inno2.
PSTN-phone calls inno1. inno1 transfers to other PSTN-phone-2.

Broadcast Group & Waiting Queue

Tested feature Result
Caller can make a call to a Broadcast Group
Caller can make a call to a Waiting Queue
Announcement if nobody picks up the call

Configuration

Firmware version

All innovaphone devices use Vx build xx-xxxxx as firmware.

SIP - Trunk

Number Mapping

Route Settings

Media Relay

Fax

Innovaphone Compatibility Test Report-old-test

Summary

SIP Provider: HFO

The provider supports all required innovaphone features and is therefore qualified as recommended SIP Provider.

HFO does not support the remote hold feature. When making a blind transfer(using redial key) the remote end will not get a MOH/dialtone from the provider.

HFO has achieved 89% of all possible test points. For more information on the test rating, please refer to Test Description

  • Features:
    • Direct Dial In
    • DTMF
  • Supported Codecs by the provider
    • G711
    • G729

Current test state

The tests for this product have been completed.

Testing of this product has been finalized October 22th, 2007.

Testing Enviroment

Scenario NAT

HFO SIP Compatibility Test 5.PNG

This scenario describes a setup where the PBX and phones are in a private network. The IP800 must use a stun server, in order to send correct SIP - messages. The IP800 works as media relay, all RTP - streams go through the PBX.

Test Results

For more information on the test procedure, please read the following wiki article: SIP Interop Test Description. Bold lines in the test results indicate a KO-criteria.

Basic Call

Tested feature Result
call using g711a Yes
call using g711u Yes
call using g723 No
call using g729 Yes
Overlapped sending No
early media channel Yes
Fax using T.38 No
CGPN can be supressed Yes
Reverse Media Negotiaton Yes
Voice Quality OK? Yes

Direct Dial In

Tested feature Result
Inbound(Provider -> Innovaphone) Yes
Outbound(Innovaphone -> Provider) Yes

DTMF

Tested feature Result
DTMF tones sent correctly Yes
DTMF tones received correctly Yes

Hold/Retrieve

Tested feature Result
Call can be put on hold Yes
Held end hears music on hold / announcement from PBX Yes
Held end hears music on hold / announcement from provider No

Transfer with consultation

Tested feature Result
Call can be transfered Yes
Held end hears music on hold Yes
Call returns to transferring device if the third

Endpoint is not available

Yes

Transfer with consultation (alerting only)

Tested feature Result
Call can be transfered Yes
Held end hears music on hold or dialing tone Yes
Call returns to transferring device if the third

Endpoint is not available

Yes

Blind Transfer

Tested feature Result
Call can be transfered Yes
Held end hears dialing tone No

Broadcast Group & Waiting Queue

Tested feature Result
Caller can make a call to a Broadcast Group Yes
Caller can make a call to a Waiting Queue Yes
Announcement if nobody picks up the call Yes

Configuration

General Information

Basic Provider Infomation: HFO


  • described in Mantis Case: 16505

Firmware version


  • IP800: 6.00 dvl-sr2 IP800[07-60600.58]
  • IP22: 6.00 dvl-sr1 IP230[07-60600.58]
  • IP200: 6.00 dvl-sr1 IP230[07-60600.58]
  • IP230: 6.00 dvl-sr1 IP230[07-60600.58]

SIP - Trunk

First of all the SIP Trunk must be configured. Here an example of our HFO - Trunk. If you want that the Gateway should act as Medialrelay, you must exchange the Gatekeeper Address (blue marking) to an private network address; for example 127.0.0.1.

HFO awaits in the From Header the complete Calling Party Number(CGPN). The default innovaphone setting is to not send the complete CGPN in the FROM - Header, but in the Preffered Identity Header. Change the setting From Header: to CGPN in user part of URI.


HFO SIP Compatibility Test 1.PNG

Number Mapping

The complicated part on this issue is the correct mapping of the outgoing and incoming numbers.

HFO SIP Compatibility Test 2.PNG

Route Settings

Because HFO, as most SIP - Providers too, doesn't support overlap sending, you must enable the blockwise sending of the phone number. You can do this by enabling Force enblock in the automatically generated Routes.

The second setting you must check is Interworking(QSIG,SIP). This feature must be enabled to properly relay suplementary services, like Hold over the SIP Trunk. If this checkbox is unchecked only basic call Information like connect and disconnect will be forwarded by the Gateway.

HFO SIP Compatibility Test 3.PNG

Media Relay

By enabling Media Relay on the PBX, The IP800 will work as an RTP - Proxy, so all RTP Streams will travel through the IP800. This mode poses a much greater load on the PBX, so the number of concurrent calls will be heavy limited.

HFO SIP Compatibility Test 4.PNG

You may wonder about the usefullness of putting the localhost address as a private network. However you must insert this entry, if the IP800 SIP GW registers at the PBX on localhost interface.


Now the PBX and the phones are setup correctly. You should be able to make call in both directions and send and receive fax messages.

Retrieved from "https://wiki.innovaphone.com/index.php?title=Howto:HFO_NGN_Connect_-_HFO_-_SIP_Provider&oldid=38069"