Howto:How to Reset IPXXX: Difference between revisions
No edit summary |
|||
(11 intermediate revisions by 8 users not shown) | |||
Line 14: | Line 14: | ||
* bringing to TFTP mode for GWLoad | * bringing to TFTP mode for GWLoad | ||
* clearing config | * clearing config | ||
* explaining the | * explaining the LED behavior | ||
Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230, IP240 | Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230, IP240 | ||
Line 21: | Line 21: | ||
If the factory reset was not successful please contact rma@innovaphone.com | If the factory reset was not successful please contact rma@innovaphone.com | ||
or look at [[Howto:Get Access to Gateways if the Assistant doesn't boot the Device]]. | |||
{| border=1 | {| border=1 | ||
!Device (visual display) | !Device (visual display) | ||
!Reset Button/ | !Reset Button/Key | ||
!Button pressed | !Button pressed | ||
!Clear Config | !Clear Config | ||
Line 37: | Line 39: | ||
!Firmware Error | !Firmware Error | ||
|---- | |---- | ||
|IP21 (all | |IP21 | ||
(all LED's) | |||
|Button | |Button | ||
|ready: <5s blink, >5s constant flash | |ready: <5s blink, >5s constant flash | ||
line1+ line2 + door + aux constant flash / link + act off | line1 + line2 + door + aux constant flash / link + act off | ||
with plugged in | with plugged in ethernet cable 100M + link: <3s off, >3s normal operating state | ||
|... | |... | ||
Line 50: | Line 53: | ||
|3 | |3 | ||
|25 | |25 | ||
|all | |all LED’s are constant flashing | ||
link is blinking | |||
|ready + line1/2 + door+ aux + 100M(if link) | |ready + line1/2 + door + aux + 100M (if link) | ||
permanent for ca. 5s | permanent for ca. 5s | ||
Line 63: | Line 66: | ||
| | | | ||
|---- | |---- | ||
|IP400 (all | |IP400 | ||
(all LED’s) | |||
|Button | |Button | ||
|PPP+Tel.1+Tel.2: < 5s blink, [5;8] constant flash, >8 ready + link + act constant flash | |PPP+Tel.1+Tel.2: <5s blink, [5;8] constant flash, >8 ready + link + act constant flash | ||
without | without ethernet cable plugged in: <8s off, 8s one blink, >8s off | ||
| | | | ||
|3 | |3 | ||
|25 | |25 | ||
| | |ready + link + act flashing constant | ||
|<8 | |<8 ready + PPP + tel1 + tel2 constant flash, | ||
[3;10] link + act. uncoordinated flashing | [3;10] link + act. uncoordinated flashing | ||
>10s | >10s ready + link (if link) constant act. blinking | ||
| | |ready + 100M (if link) | ||
link blinking | link blinking | ||
| | | | ||
|---- | |---- | ||
|IP3000 (all | |IP3000 | ||
(all LED’s) | |||
|Button | |Button | ||
|<6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash, | |<6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash, | ||
Line 90: | Line 95: | ||
>10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off | >10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off | ||
with | with ethernet cable plugged in: act + speed + link normal working state | ||
| | |fast blink (green) | ||
|3 | |3 | ||
|25 | |25 | ||
|all | |all LED’s flashing permanent | ||
ready off | ready off | ||
Line 105: | Line 110: | ||
>5s ready constant flash, (if link) link + speed constant flashing, act blinking | >5s ready constant flash, (if link) link + speed constant flashing, act blinking | ||
|ready constant flash, (if link) link + speed constant flashing, act blinking | |ready constant flash, (if link) link + speed constant flashing, act blinking | ||
| | |blinking (green) | ||
|---- | |---- | ||
|IP800 / IP6000 | |IP800/IP6000/IPx010 | ||
(red/green/orange ready LED ) | (red/green/orange ready LED ) | ||
|Button | |Button | ||
Line 118: | Line 122: | ||
<13 constant orange | <13 constant orange | ||
| | |fast blink (green) | ||
|3 | |3 | ||
|15 (IP800) | |15 (IP800) | ||
15-20 (IP6000) | 15-20 (IP6000/IPx010) | ||
|constant orange | |constant orange | ||
| | |red | ||
| | |green | ||
| | |blinking (red) | ||
|---- | |---- | ||
|IP1200 | |IP1200 | ||
|Button | |Button | ||
|<2s | |<2s alarm red constant flash, ready off | ||
[2;7] | [2;7] alarm off, ready slow blink green | ||
[7;13] | [7;13] alarm off, ready fast blink green | ||
>13s | >13s alarm off, ready 2 Hz blink green | ||
| | |fast blink | ||
|3 | |3 | ||
|10 | |10 | ||
| | |slow flash ca. 2 Hz | ||
|<2s | |<2s alarm red constant flash | ||
ready green constant flash | ready green constant flash | ||
power orange constant flash | |||
[2;4] | [2;4] alarm off, ready off, power orange | ||
>4s | >4s alarm off, ready constant green flash, power constant green flash | ||
| | |ready constant green flash and power constant orange flash | ||
| | |alarm (red) | ||
|---- | |---- | ||
|IP200/IP202 (red handset) | |IP1202/IP1203 | ||
| | |Button | ||
| | |<3s LED off | ||
| | |||
[3;10] LED blink fast blue 1 sec | |||
>10s LED blink fast blue 1 sec, | |||
than blink slow blue until factory reset completed, | |||
than constant yellow/amber | |||
|fast blink in blue | |||
|3 | |||
|10 | |||
|constant yellow/amber | |||
|LED red until firmware lstarted | |||
LED blink fast red until ethernet link up | |||
LED blink fast blue until Air Sync established | |||
LED constant blue if Air Sync OK | |||
|LED constant blue | |||
|LED constant red | |||
|---- | |||
|IP200/IP202 | |||
(red handset) | |||
|alt key | |||
|slow blink | |||
|slow blink | |||
|3 | |3 | ||
|5 | |5 | ||
| | |constant flash | ||
| | |slow blink | ||
| | |off | ||
| | |constant flash | ||
|---- | |---- | ||
|IP200A/IP210 (red handset) | |IP200A/IP210 | ||
| | (red handset) | ||
| | |alt key | ||
| | |slow blink | ||
|fast blink | |||
|3 | |3 | ||
|15 | |15 | ||
| | |slow flash | ||
| | ca. 2 Hz | ||
| | |on | ||
| | |off | ||
|blinking | |||
|---- | |---- | ||
| | |IP110 | ||
(LED’s in F1 key) | |||
|save key | |||
|slow blink | |||
|F1 off | |||
| | |||
| | |||
|F1 | |||
|3 | |3 | ||
|10 - 15 | |10 - 15 | ||
| | |slow flash | ||
ca. 2 Hz | |||
|constant F1 flash | |constant F1 flash | ||
| | |off | ||
| | |blinking | ||
|---- | |---- | ||
| | |IP101 | ||
| | (MWI LED) | ||
|backspace key | |||
|press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink | |||
| | | | ||
| | | | ||
| | |||
| | |||
| | |||
| | |||
| | |||
|---- | |||
|IP102 | |||
(MWI LED) | |||
|backspace key | |||
|press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink | |||
| | |||
| | |||
| | |||
| | |||
| | |||
| | |||
| | |||
|---- | |||
|IP111 | |||
(MWI LED) | |||
|home key | |||
|press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink | |||
| | |||
| | |||
| | |||
| | |||
| | |||
| | |||
| | |||
|---- | |||
|IP112 | |||
(MWI LED) | |||
|home key | |||
|press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink | |||
| | |||
| | |||
| | |||
| | |||
| | |||
| | |||
| | |||
|---- | |||
|IP230 | |||
(menu key) | |||
|menu key | |||
|slow blink | |||
|fast blink | |||
|3 | |||
|10 | |||
|slow flash | |||
ca. 2 Hz | |||
|on | |||
|off | |||
|blinking | |||
|---- | |||
|IP240 | |||
(menu key) | |||
|menu key | |||
|slow blink | |||
|fast blink | |||
|3 | |3 | ||
|10 | |10 | ||
| | |slow flash | ||
| | ca. 2 Hz | ||
| | |on | ||
| | |off | ||
|blinking | |||
|---- | |---- | ||
|IP241 ( | |IP241 | ||
| | (menu key) | ||
|alt key | |||
|slow blink | |slow blink | ||
| | |fast blink | ||
|3 | |3 | ||
|10 | |10 | ||
| | |slow flash | ||
| | ca. 2 Hz | ||
| | |on | ||
| | |off | ||
|blinking | |||
|---- | |---- | ||
|IP222 (MWI LED) | |IP222 | ||
|ESC key | (MWI LED) | ||
|ESC key or Home key | |||
|slow blink | |slow blink | ||
| | |fast blink | ||
|3 | |3 | ||
|15 | |15 | ||
| | |slow flash | ||
| | ca. 2 Hz | ||
| | |on | ||
| | |off | ||
|blinking | |||
|---- | |---- | ||
|IP232 (MWI LED) | |IP232 | ||
|ESC key | (MWI LED) | ||
|ESC key or Home key | |||
|slow blink | |slow blink | ||
| | |fast blink | ||
|3 | |3 | ||
|15 | |15 | ||
| | |slow flash | ||
| | ca. 2 Hz | ||
| | |on | ||
| | |off | ||
|blinking | |||
|} | |} | ||
== Related Articles == | == Related Articles == | ||
[[Howto:How to use gwload]] | * [[Howto:How to use gwload]] | ||
* [[Howto:How_to_Reset_IPXXX_(V10...)]] | |||
[[Category:Howto|{{PAGENAME}}]] | [[Category:Howto|{{PAGENAME}}]] |
Latest revision as of 10:39, 18 December 2023
Summary
Different Reset Options of IPXXX
Applies To
This information applies to
- All innovaphone products with the latest boot code.
More Information
Different options resetting innovaphone devices.
- bringing to Factory default
- bringing to TFTP mode for GWLoad
- clearing config
- explaining the LED behavior
Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230, IP240
Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table. If you want to reanimate this devices now with GWLoad, do not powercycle the device again. If the factory reset was successful the device is now in the defined TFTP-Mode and ready for GWLoad. If you just wanted to factory reset the device you can do a powercycle for sure.
If the factory reset was not successful please contact rma@innovaphone.com
or look at Howto:Get Access to Gateways if the Assistant doesn't boot the Device.
Device (visual display) | Reset Button/Key | Button pressed | Clear Config
Firmware Boot code update |
Pressing Button to TFTP without deleting config in seconds ca. | Pressing Button to factory reset in seconds ca. | GWLoad- / TFTP-Mode | Firmware starting | Firmware ready | Firmware Error |
---|---|---|---|---|---|---|---|---|---|
IP21
(all LED's) |
Button | ready: <5s blink, >5s constant flash
line1 + line2 + door + aux constant flash / link + act off with plugged in ethernet cable 100M + link: <3s off, >3s normal operating state |
...
ready fast blink, line1 + line2 + door + aux off link + 100M normal operating |
3 | 25 | all LED’s are constant flashing
link is blinking |
ready + line1/2 + door + aux + 100M (if link)
permanent for ca. 5s link blinking |
ready + 100M (if link)
link blinking |
|
IP400
(all LED’s) |
Button | PPP+Tel.1+Tel.2: <5s blink, [5;8] constant flash, >8 ready + link + act constant flash
without ethernet cable plugged in: <8s off, 8s one blink, >8s off |
3 | 25 | ready + link + act flashing constant | <8 ready + PPP + tel1 + tel2 constant flash,
[3;10] link + act. uncoordinated flashing >10s ready + link (if link) constant act. blinking |
ready + 100M (if link)
link blinking |
||
IP3000
(all LED’s) |
Button | <6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,
act + speed + link off >10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off with ethernet cable plugged in: act + speed + link normal working state |
fast blink (green) | 3 | 25 | all LED’s flashing permanent
ready off link blinking |
>2 link + speed constant flashing, act blinking
<5s PRI1 + PRI2 + S/T constant flash >5s ready constant flash, (if link) link + speed constant flashing, act blinking |
ready constant flash, (if link) link + speed constant flashing, act blinking | blinking (green) |
IP800/IP6000/IPx010
(red/green/orange ready LED ) |
Button | <6 slow gn blink
[6;10] constant red [10;13] fast gn blink <13 constant orange |
fast blink (green) | 3 | 15 (IP800)
15-20 (IP6000/IPx010) |
constant orange | red | green | blinking (red) |
IP1200 | Button | <2s alarm red constant flash, ready off
[2;7] alarm off, ready slow blink green [7;13] alarm off, ready fast blink green >13s alarm off, ready 2 Hz blink green |
fast blink | 3 | 10 | slow flash ca. 2 Hz | <2s alarm red constant flash
ready green constant flash power orange constant flash [2;4] alarm off, ready off, power orange >4s alarm off, ready constant green flash, power constant green flash |
ready constant green flash and power constant orange flash | alarm (red) |
IP1202/IP1203 | Button | <3s LED off
[3;10] LED blink fast blue 1 sec >10s LED blink fast blue 1 sec, than blink slow blue until factory reset completed, than constant yellow/amber |
fast blink in blue | 3 | 10 | constant yellow/amber | LED red until firmware lstarted
LED blink fast red until ethernet link up LED blink fast blue until Air Sync established LED constant blue if Air Sync OK |
LED constant blue | LED constant red |
IP200/IP202
(red handset) |
alt key | slow blink | slow blink | 3 | 5 | constant flash | slow blink | off | constant flash |
IP200A/IP210
(red handset) |
alt key | slow blink | fast blink | 3 | 15 | slow flash
ca. 2 Hz |
on | off | blinking |
IP110
(LED’s in F1 key) |
save key | slow blink | F1 off | 3 | 10 - 15 | slow flash
ca. 2 Hz |
constant F1 flash | off | blinking |
IP101
(MWI LED) |
backspace key | press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink | |||||||
IP102
(MWI LED) |
backspace key | press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink | |||||||
IP111
(MWI LED) |
home key | press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink | |||||||
IP112
(MWI LED) |
home key | press key when power cycle, hold ca 10 sec till led flashing. Power cycle again when slow blink | |||||||
IP230
(menu key) |
menu key | slow blink | fast blink | 3 | 10 | slow flash
ca. 2 Hz |
on | off | blinking |
IP240
(menu key) |
menu key | slow blink | fast blink | 3 | 10 | slow flash
ca. 2 Hz |
on | off | blinking |
IP241
(menu key) |
alt key | slow blink | fast blink | 3 | 10 | slow flash
ca. 2 Hz |
on | off | blinking |
IP222
(MWI LED) |
ESC key or Home key | slow blink | fast blink | 3 | 15 | slow flash
ca. 2 Hz |
on | off | blinking |
IP232
(MWI LED) |
ESC key or Home key | slow blink | fast blink | 3 | 15 | slow flash
ca. 2 Hz |
on | off | blinking |