Howto:Innovaphone Phones on FritzBox: Difference between revisions
Mediarunway (talk | contribs) |
|||
(12 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
{{Template:3rd Party Input}} | |||
==Applies To== | ==Applies To== | ||
This information applies to | This information applies to | ||
Line 10: | Line 11: | ||
===Configuration FritzBox User=== | ===Configuration FritzBox User=== | ||
Configure user within FritzBox-admin-menu as shown below. | |||
Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) '''must not''' match or resemble the choosen username (Benutzername). | |||
Although no error is displayed, later on phone login will just not work. | |||
[[Image:Fritz1.PNG]] | [[Image:Fritz1.PNG]] | ||
===Configuration innovaphone User Config=== | ===Configuration innovaphone User Config=== | ||
Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232"). | |||
Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this: | |||
[[Image:Innofritz.png]] | [[Image:Innofritz.png]] | ||
'''Attention !''' | |||
Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722" as well the Protocol must be set to SIP/TCP. | |||
===Configuration Message Waiting Key=== | ===Configuration Message Waiting Key=== | ||
Line 37: | Line 49: | ||
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3". | Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3". | ||
[[Image:Innofritz-on-off. | [[Image:Innofritz-on-off.png]] | ||
===Known Problems=== | ===Known Problems=== |
Latest revision as of 09:48, 14 February 2023
Applies To
This information applies to
innovaphone IP Phones User Configuration for registering on FritzBox
More Information
Configuration FritzBox User
Configure user within FritzBox-admin-menu as shown below.
Remark: According to experiences with current hard- and software (FB7590, 7.00), selected password (Kennwort) must not match or resemble the choosen username (Benutzername). Although no error is displayed, later on phone login will just not work.
Configuration innovaphone User Config
Login to the webbased user interface of the phone via webbrowser. Insert ip-adress of phone to your browser and login with userid "admin" and password "ipxxx" where xxx stands for the phone type (e.g. IP232 has default password "ip232").
Then step to Phone/User-1 and configure the innovaphone user with the data used in FritzBox like this:
Attention !
Since Fritz Box Firmware Version 7.50 the General Coder Preference must be set at least to "G722" as well the Protocol must be set to SIP/TCP.
Configuration Message Waiting Key
innovaphone phones support RFC 3842 which defines SIP based message waiting procedure.
This enables definition and use of message waiting function key and lamp to access FritzBox-built-in voicemail service.
By default, FritzBox-VM owns number **600. Any further described configuration assume this as default. If this is changed by user or manufacturer, configuration below has to be adapted.
Control of MWI-LED and voicemail access via function key requires definition of both number and name as follows:
- Number: <FritzBox-VM>@fritz.box - default **600@fritz.box ; do NOT tick Append Own Number
- Name: <username>@fritz.box
Voicemail on/off Key
Add an "Dial" function key. Insert in Action>Number the Fritz-Box-VM owns number **600, followed from one waiting command "," and the FritBox-VM DTMF Command for on/off "3".