Howto:Analog Trunk (FXO) with Linksys SPA3102: Difference between revisions

From innovaphone wiki
Jump to navigation Jump to search
← Older editNewer edit →
VisualWikitext
mNo edit summary
Line 103: Line 103:
|call using g711a
|call using g711a
|yes
|yes
|
|----
|----
|call using g711u
|call using g711u
|yes
|yes
|
|----
|----
|call using g723
|call using g723
|yes
|yes
|
|----
|----
|call using g729
|call using g729
|yes
|yes
|
|----
|----
|Overlapped sending
|Overlapped sending
|yes
|yes
|
|----
|----
|early media channel
|early media channel
|not tested
|not tested
|
|----
|----
|Fax
|Fax
|not tested
|not tested
|
|----
|----
|Voice Quality OK?
|Voice Quality OK?
|yes
|yes
|
|}
|}


Line 143: Line 135:
|Inbound(Sipura -> innovaphone)
|Inbound(Sipura -> innovaphone)
|yes
|yes
|
|----
|----
|Outbound(Innovaphone -> Sipura)
|Outbound(Innovaphone -> Sipura)
|yes
|yes
|
|}
|}


Line 159: Line 149:
|DTMF tones sent correctly
|DTMF tones sent correctly
|yes
|yes
|
|----
|----
|DTMF tones received correctly (audible)
|DTMF tones received correctly (audible)
|yes
|yes
|
|}
|}


Line 175: Line 163:
|Device can put call on hold
|Device can put call on hold
|yes
|yes
|
|----
|----
|Held end hears music on hold
|Held end hears music on hold
|yes
|yes
|
|----
|----
|Device can terminate either call and retrieve remaining call
|Device can terminate either call and retrieve remaining call
|yes
|yes
|
|}
|}


Line 195: Line 180:
|Device can transfer call
|Device can transfer call
|yes
|yes
|
|----
|----
|Held end hears music on hold
|Held end hears music on hold
|yes
|yes
|
|----
|----
|Call returns to transferring device if the third  
|Call returns to transferring device if the third  
Endpoint is not available
Endpoint is not available
|yes
|yes
|
|}
|}


Line 216: Line 198:
|Device can transfer call
|Device can transfer call
|yes
|yes
|
|----
|----
|Held end hears music on hold or dialing tone
|Held end hears music on hold or dialing tone
|yes
|yes
|
|----
|----
|Call returns to transferring device if the third  
|Call returns to transferring device if the third  
Endpoint is not available
Endpoint is not available
|yes
|yes
|
|}
|}


Line 237: Line 216:
|Device can transfer call
|Device can transfer call
|yes
|yes
|
|----
|----
|Held end hears dialing tone
|Held end hears dialing tone
|no - hears nothing
|no - hears nothing
|
|}
|}


Line 253: Line 230:
|Caller can make a call to a Broadcast Group
|Caller can make a call to a Broadcast Group
|yes
|yes
|
|----
|----
|Caller can make a call to a Waiting Queue
|Caller can make a call to a Waiting Queue
|yes
|yes
|
|----
|----
|Announcement if nobody picks up the call
|Announcement if nobody picks up the call
|yes
|yes
|
|}
|}


Line 273: Line 247:
|CGPN is displayed correctly
|CGPN is displayed correctly
|no
|no
|
|----
|----
|CGPN can be supressed
|CGPN can be supressed
|yes
|yes
|
|}
|}


Revision as of 11:21, 9 April 2008

Innovaphone Compatibility Test Report

Linksys (Sipura) SPA:3102

Infomation:

  • Software Version 3.3.6(GW)
  • Hardware version 1.3.5(a)

innovaphone gateway/pbx

This information applies to

  • all PBX Platforms

6.00 dvl-sr2 IP800[07-60698]or higher

configuration

With this configuration you can dial the whole number at once . you don´t have to wait for the analog dial tone.

For connecting the Linksys for Analog Trunk ( FXO ) connection to the innovaphone Gateway/pbx you need a Gatekeeper/Registrar license.

Linksys configuration

Configuration of the proxy settings

Proxy: Ip address of the innovaphone Gateway/Pbx

user id: the registration name to the innovaphone Gateway/Pbx



Voip to PSTN gateway enable set to yes

Line Voip caller DP set to none

One stage dialing set to no


innovaphone configuration

Configure a registrar where the Linksys can register (as seen in picture below)

administration/gateway/voip


Configure a route to the Linksys

number out is here a 0 - you can take any digit this is for the analog trunk assignment.

Then you configure a " ^ " this indicates an Delay for one second , then the rest of the number will be dialed in dtmf with 300msec delay between every digit.


For incoming calls (from analog Trunk to innovaphone) you have to configure the proper routes - from the GW where the Sipura is connected to the pbx.



Supported Codecs

Codec Applies
G711 yes
G729 yes
G723 yes
G726 yes
GSM no
T.38 UDP no
G722 No


Test Results

Basic Call

Tested feature Result
call using g711a yes
call using g711u yes
call using g723 yes
call using g729 yes
Overlapped sending yes
early media channel not tested
Fax not tested
Voice Quality OK? yes


Dial Inward

Tested feature Result
Inbound(Sipura -> innovaphone) yes
Outbound(Innovaphone -> Sipura) yes


DTMF

Tested feature Result
DTMF tones sent correctly yes
DTMF tones received correctly (audible) yes


Hold/Retrieve

Tested feature Result
Device can put call on hold yes
Held end hears music on hold yes
Device can terminate either call and retrieve remaining call yes


Transfer with consultation

Tested feature Result
Device can transfer call yes
Held end hears music on hold yes
Call returns to transferring device if the third

Endpoint is not available

yes


Transfer with consultation (alerting only)

Tested feature Result
Device can transfer call yes
Held end hears music on hold or dialing tone yes
Call returns to transferring device if the third

Endpoint is not available

yes


Blind Transfer

Tested feature Result
Device can transfer call yes
Held end hears dialing tone no - hears nothing


Broadcast Group & Waiting Queue

Tested feature Result
Caller can make a call to a Broadcast Group yes
Caller can make a call to a Waiting Queue yes
Announcement if nobody picks up the call yes


Calling Party Number

Tested feature Result
CGPN is displayed correctly no
CGPN can be supressed yes
Retrieved from "https://wiki.innovaphone.com/index.php?title=Howto:Analog_Trunk_(FXO)_with_Linksys_SPA3102&oldid=9087"