Howto:How to Reset IPXXX
Summary
Different Reset Options of IPXXX
Applies To
This information applies to
- All innovaphone products with the latest boot code.
More Information
Different options resetting innovaphone devices.
- bringing to Factory default
- bringing to TFTP mode for GWLoad
- clearing config
- explaining the Led behavior
Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230
Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table.
| Device (visual display) | Reset Button/key | Button pressed | Clear Config
Firmware Boot code update |
Pressing Button to TFTP without deleting config in seconds ca. | Pressing Button to factory reset in seconds ca. | GWLoad- / TFTP-Mode | Firmware starting | Firmware ready | Firmware Error |
|---|---|---|---|---|---|---|---|---|---|
| IP21 (all LEDs) | Button | ready: <5s blink, >5s constant flash
line1+ line2 + door + aux constant flash / link + act off with plugged in Ethernet cable 100M + link: <3s off, >3s normal operating state |
...
ready fast blink, line1 + line2 + door + aux off link + 100M normal operating |
3 | 25 | all Led’s are constant flashing
Link is blinking |
ready + line1/2 + door+ aux + 100M(if link)
permanent for ca. 5s link blinking |
ready + 100M (if link)
link blinking |
|
| IP400 (all Led’s) | Button | PPP+Tel.1+Tel.2: < 5s blink, [5;8] constant flash, >8 ready + link + act constant flash
without Ethernet cable plugged in: <8s off, 8s one blink, >8s off |
3 | 25 | Ready + Link + Act flashing constant | <8 Ready + PPP + Tel1 + Tel2 constant flash,
[3;10] link + act. uncoordinated flashing >10s Ready + link (if link) constant act. blinking |
Ready + 100M (if link)
link blinking |
||
| IP3000 (all Led’s) | Button | <6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,
act + speed + link off >10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off with Ethernet cable plugged in: act + speed + link normal working state |
Fast blink (green) | 3 | 25 | all Led’s flashing permanent
ready off link blinking |
>2 link + speed constant flashing, act blinking
<5s PRI1 + PRI2 + S/T constant flash >5s ready constant flash, (if link) link + speed constant flashing, act blinking |
ready constant flash, (if link) link + speed constant flashing, act blinking | Blinking (green) |
| IP800 / IP6000
(red/green/orange ready LED ) |
Button | <6 slow gn blink
[6;10] constant red [10;13] fast gn blink <13 constant orange |
Fast blink (green) | 3 | 15 (IP800)
15-20 (IP6000) |
constant orange | Red | Green | Blinking (red) |
| IP1200 | Button | <2s Alarm red constant flash, ready off
[2;7] Alarm off, ready slow green blink [7;13] Alarm off, read fast blink green >13s Alarm off, ready 2 Hz blink green |
Fast blink | 3 | 10 | Slow flash ca. 2 Hz | <2s Alarm red constant flash
ready green constant flash Power orange constant flash [2;4] Alarm off, ready off, Power orange >4s Alarm off, ready constant green flash, Power constant green flash |
Ready constant green flash and power constant orange flash | Alarm (red) |
| IP200/IP202 (red handset) | Alt key | Slow blink | Slow blink | 3 | 5 | Constant flash | Slow blink | Off | Constant flash |
| IP200A/IP210 (red handset) | Alt key | Slow blink | Fast blink | 3 | 15 | Slow flash ca. 2 Hz | On | Off | Blinking |
| IP230 (Menu key) | Menu key | Slow blink | Fast blink | 3 | 10 | Slow flash ca. 2 Hz | On | Off | Blinking |
| IP110 (Led’s in F1-F4 key) | Save key | Slow blink | F1-F4 off | 3 | 10 - 15 | Slow flash ca. 2 Hz | constant F1 flash | Off | Blinking |