Howto:How to Reset IPXXX
Summary
Different Reset Options of IPXXX
Applies To
This information applies to
- All innovaphone products with the latest boot code.
More Information
Different options resetting innovaphone devices.
- bringing to Factory default
- bringing to TFTP mode for GWLoad
- clearing config
- explaining the LED behavior
Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230, IP240
Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table. If you want to reanimate this devices now with GWLoad, do not powercycle the device again. If the factory reset was successful the device is now in the defined TFTP-Mode and ready for GWLoad. If you just wanted to factory reset the device you can do a powercycle for sure.
If the factory reset was not successful please contact rma@innovaphone.com
Device (visual display) | Reset Button/Key | Button pressed | Clear Config
Firmware Boot code update |
Pressing Button to TFTP without deleting config in seconds ca. | Pressing Button to factory reset in seconds ca. | GWLoad- / TFTP-Mode | Firmware starting | Firmware ready | Firmware Error |
---|---|---|---|---|---|---|---|---|---|
IP21
(all LED's) |
Button | ready: <5s blink, >5s constant flash
line1 + line2 + door + aux constant flash / link + act off with plugged in ethernet cable 100M + link: <3s off, >3s normal operating state |
...
ready fast blink, line1 + line2 + door + aux off link + 100M normal operating |
3 | 25 | all LED’s are constant flashing
link is blinking |
ready + line1/2 + door + aux + 100M (if link)
permanent for ca. 5s link blinking |
ready + 100M (if link)
link blinking |
|
IP400
(all LED’s) |
Button | PPP+Tel.1+Tel.2: <5s blink, [5;8] constant flash, >8 ready + link + act constant flash
without ethernet cable plugged in: <8s off, 8s one blink, >8s off |
3 | 25 | ready + link + act flashing constant | <8 ready + PPP + tel1 + tel2 constant flash,
[3;10] link + act. uncoordinated flashing >10s ready + link (if link) constant act. blinking |
ready + 100M (if link)
link blinking |
||
IP3000
(all LED’s) |
Button | <6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash,
act + speed + link off >10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off with ethernet cable plugged in: act + speed + link normal working state |
fast blink (green) | 3 | 25 | all LED’s flashing permanent
ready off link blinking |
>2 link + speed constant flashing, act blinking
<5s PRI1 + PRI2 + S/T constant flash >5s ready constant flash, (if link) link + speed constant flashing, act blinking |
ready constant flash, (if link) link + speed constant flashing, act blinking | blinking (green) |
IP800/IP6000/IPx010
(red/green/orange ready LED ) |
Button | <6 slow gn blink
[6;10] constant red [10;13] fast gn blink <13 constant orange |
fast blink (green) | 3 | 15 (IP800)
15-20 (IP6000/IPx010) |
constant orange | red | green | blinking (red) |
IP1200 | Button | <2s alarm red constant flash, ready off
[2;7] alarm off, ready slow blink green [7;13] alarm off, ready fast blink green >13s alarm off, ready 2 Hz blink green |
fast blink | 3 | 10 | slow flash ca. 2 Hz | <2s alarm red constant flash
ready green constant flash power orange constant flash [2;4] alarm off, ready off, power orange >4s alarm off, ready constant green flash, power constant green flash |
ready constant green flash and power constant orange flash | alarm (red) |
IP1202 | Button | <3s LED off
[3;10] LED blink fast blue 1 sec >10s LED blink fast blue 1 sec, than blink slow blue until factory reset completed, than constant yellow/amber |
fast blink in blue | 3 | 10 | constant yellow/amber | LED red until firmware lstarted
LED blink fast red until ethernet link up LED blink fast blue until Air Sync established LED constant blue if Air Sync OK |
LED constant blue | LED constant red |
IP200/IP202
(red handset) |
alt key | slow blink | slow blink | 3 | 5 | constant flash | slow blink | off | constant flash |
IP200A/IP210
(red handset) |
alt key | slow blink | fast blink | 3 | 15 | slow flash
ca. 2 Hz |
on | off | blinking |
IP110
(LED’s in F1 key) |
save key | slow blink | F1 off | 3 | 10 - 15 | slow flash
ca. 2 Hz |
constant F1 flash | off | blinking |
IP111
(MWI LED) |
home key | ||||||||
IP112
(MWI LED) |
home key | ||||||||
IP230
(menu key) |
menu key | slow blink | fast blink | 3 | 10 | slow flash
ca. 2 Hz |
on | off | blinking |
IP240
(menu key) |
menu key | slow blink | fast blink | 3 | 10 | slow flash
ca. 2 Hz |
on | off | blinking |
IP241
(menu key) |
alt key | slow blink | fast blink | 3 | 10 | slow flash
ca. 2 Hz |
on | off | blinking |
IP222
(MWI LED) |
ESC key | slow blink | fast blink | 3 | 15 | slow flash
ca. 2 Hz |
on | off | blinking |
IP232
(MWI LED) |
ESC key | slow blink | fast blink | 3 | 15 | slow flash
ca. 2 Hz |
on | off | blinking |