Howto:How to use the IP21 DOOR interface: Difference between revisions
m (→Installation) |
mNo edit summary |
||
(11 intermediate revisions by one other user not shown) | |||
Line 2: | Line 2: | ||
This information applies to | This information applies to | ||
* | *IP21, V4,V5,V6 | ||
<!-- | <!-- tfe türfreisprecheinrichtung --> | ||
==More Information== | ==More Information== | ||
Line 13: | Line 13: | ||
Following there is a short compatibility list and some installations tips. | Following there is a short compatibility list and some installations tips. | ||
===System Requirements=== | ===System Requirements=== | ||
Line 24: | Line 23: | ||
===Installation=== | ===Installation=== | ||
In the gateway manual (or see attached How to use the IP21 DOOR interface IP21TFE.zip) you will find a table called pin assignment. | In the gateway manual (or see attached [[media:Howto-How to use the IP21 DOOR interface IP21TFE.zip|ZIP file]]) you will find a table called pin assignment. | ||
====DOOR Interface Pinout==== | |||
This is the relation between symbolic and real pins: | |||
{|border="2" cellspacing="4" cellpadding="3" rules="all" style="margin:1em 1em 1em 0; border:solid 1px #AAAAAA; border-collapse:collapse;empty-cells:show;" | |||
!Pin | |||
!Identifier | |||
!Description | |||
!Beschreibung | |||
|---- | |||
|1 | |||
|E1 | |||
|Overhear block | |||
|Mithörersperre | |||
|---- | |||
|2 | |||
|E2 | |||
|Overhear block | |||
|Mithörersperre | |||
|---- | |||
|3 | |||
|K2 | |||
|Door-bell button 2 | |||
|Klingel Eingang 2 | |||
|---- | |||
|4 | |||
|K1 | |||
|Door-bell button 1 | |||
|Klingel Eingang 1 | |||
|---- | |||
|5 | |||
|K | |||
|Reference point for bell buttons | |||
|Bezugspunkt – Klingel | |||
|---- | |||
|6 | |||
|11 | |||
|Door-Opener 1 | |||
|Türöffner 1 | |||
|---- | |||
|7 | |||
|53 | |||
|Door-Opener 1, relay (max. 2A) short circuit with <nowiki>#</nowiki>, open with 0 | |||
|Türöffner 1, Relais (max. 2A) wird mit # geschlossen und mit 0 geöffnet | |||
|---- | |||
|8 | |||
|69 | |||
| | |||
| | |||
|---- | |||
|9 | |||
|<nowiki>+</nowiki> | |||
|microphone/speaker voltage | |||
|Spannung für Mikrofon und Lautsprecher | |||
|---- | |||
|10 | |||
|2 | |||
|Speaker Mass | |||
|Lautsprecher Masse | |||
|---- | |||
|11 | |||
|6 | |||
|Audio In/Micro | |||
|Hörer/Mikrofon Masse | |||
|---- | |||
|12 | |||
|13 | |||
| | |||
| | |||
|---- | |||
|13 | |||
|12 | |||
|Audio out, Indoor phone voltage | |||
|Analog Ausgang, Wohntelefon Spannung | |||
|---- | |||
|14 | |||
|X | |||
|Door-Opener 2 | |||
|Türöffner 2 | |||
|---- | |||
|15 | |||
|Y | |||
|Door-Opener 2, relay (max. 2A) short circuit with <nowiki>*</nowiki>, open with 0 | |||
|Türöffner 2, Relais (max. 2A) wird mit * geschlossen und mit 0 geöffnet | |||
|} | |||
IP21 – backside: | IP21 – backside: | ||
Power – Ethernet – Reset – Tel1 – Tel2 – AUX – DOOR pin 1 … 15 | Power – Ethernet – Reset – Tel1 – Tel2 – AUX – DOOR pin 1 … 15 | ||
A description of the Door Interface could be found in the following schematics. This documents, describing the wiring of several door interfaces like SIEDLE(TM) and others, could be found on the link below as PDF. | |||
[[Image:IP21 door siedle TLM511.png|thumb|400px|center|Siedle TLM511]] | |||
[[Image:IP21 door siedle TL352.png|thumb|400px|center|Siedle TL352]] | |||
[[Image:IP21 door Ritto.png|thumb|400px|center|Ritto]] | |||
[[Image:IP21 door Tiptel TSS2.png|thumb|400px|center|Tiptel TSS2]] | |||
===Known Problems=== | ===Known Problems=== | ||
The WT mode and non WT mode assignment is different | The WT mode and non WT mode assignment is different - see schematics or contact support@innovaphone.com therefore. | ||
Doorline Systems with the standard "FTZ 123 D12" are not supported by IP21 gateway. | |||
===Known Problems=== | ===Known Problems=== |
Latest revision as of 20:22, 20 June 2011
Applies To
This information applies to
- IP21, V4,V5,V6
More Information
The door interface of the IP21 is built for connections between door openers.
Some of the door system are outdated and have been replaced with newer models.
Following there is a short compatibility list and some installations tips.
System Requirements
The IP21 DOOR interface supports only Doorline systems:
- Tiptel TSS 2
- Siedle TLM 511
- Siedle LM 511
- Siedle TL 352
- Ritto 5760/…
Installation
In the gateway manual (or see attached ZIP file) you will find a table called pin assignment.
DOOR Interface Pinout
This is the relation between symbolic and real pins:
Pin | Identifier | Description | Beschreibung |
---|---|---|---|
1 | E1 | Overhear block | Mithörersperre |
2 | E2 | Overhear block | Mithörersperre |
3 | K2 | Door-bell button 2 | Klingel Eingang 2 |
4 | K1 | Door-bell button 1 | Klingel Eingang 1 |
5 | K | Reference point for bell buttons | Bezugspunkt – Klingel |
6 | 11 | Door-Opener 1 | Türöffner 1 |
7 | 53 | Door-Opener 1, relay (max. 2A) short circuit with #, open with 0 | Türöffner 1, Relais (max. 2A) wird mit # geschlossen und mit 0 geöffnet |
8 | 69 | ||
9 | + | microphone/speaker voltage | Spannung für Mikrofon und Lautsprecher |
10 | 2 | Speaker Mass | Lautsprecher Masse |
11 | 6 | Audio In/Micro | Hörer/Mikrofon Masse |
12 | 13 | ||
13 | 12 | Audio out, Indoor phone voltage | Analog Ausgang, Wohntelefon Spannung |
14 | X | Door-Opener 2 | Türöffner 2 |
15 | Y | Door-Opener 2, relay (max. 2A) short circuit with *, open with 0 | Türöffner 2, Relais (max. 2A) wird mit * geschlossen und mit 0 geöffnet |
IP21 – backside:
Power – Ethernet – Reset – Tel1 – Tel2 – AUX – DOOR pin 1 … 15
A description of the Door Interface could be found in the following schematics. This documents, describing the wiring of several door interfaces like SIEDLE(TM) and others, could be found on the link below as PDF.
Known Problems
The WT mode and non WT mode assignment is different - see schematics or contact support@innovaphone.com therefore.
Doorline Systems with the standard "FTZ 123 D12" are not supported by IP21 gateway.