Howto:How to use the R-key handling: Difference between revisions
No edit summary |
m (→Configuration) |
||
(9 intermediate revisions by 5 users not shown) | |||
Line 1: | Line 1: | ||
The IP1200 could enable or disable the R-Key handling which is necessary for transferring calls. | The IP1200 & IP1202/IP1203 could enable or disable the R-Key handling which is necessary for transferring calls. | ||
<!-- Keywords: Transfer Dect Rkey R-Key forward callforward --> | |||
===Applies To=== | ===Applies To=== | ||
This information applies to | This information applies to | ||
* | *IP1200, IP1202, IP1203 | ||
* | *IP21, IP22, IP24, IP28, IP29, IP302, IP311, IP411 - Analog Phones | ||
* | *IP110 in hands-free mode | ||
Build V6 and later | Build V6 and later | ||
Line 16: | Line 17: | ||
===Configuration=== | ===Configuration=== | ||
Enable the “local R-key handling” at the | Enable the “local R-key handling” at the DECT-base in DECT/Config/System . | ||
===Usage=== | ===Usage=== | ||
Line 25: | Line 26: | ||
Use the following codes: | Use the following codes: | ||
* | * 0 – reject call waiting <!-- anklopfen anklopfer abweisen --> | ||
* 1 – disconnect held call | |||
* | * 2 – change between call 1 and call 2 <!-- makeln --> | ||
* 3 – 3-party (3PTY) conference ([[Howto:3-party_(3PTY)_conference_on_analog_or_DECT_phones|if supported]]) | |||
* | * 4 – transfer call 1 to call 2 <!-- vermitteln --> | ||
Line 36: | Line 36: | ||
* accept incoming call | * accept incoming call | ||
* press R once | * press R once | ||
* dial the second extension | * dial the second extension | ||
* press R2 to change between call 1 and call 2 or press R-key twice | |||
* press R2 to change between call 1 and call 2 | |||
* press R4 to transfer both calls | * press R4 to transfer both calls | ||
R+1 - return back to base call after pressing the R-Key | To get back to the base call after pressing R-Key use: R+1 - return back to base call after pressing the R-Key | ||
To get back to the base call after forwarding the base call to another extension also use R+1. | To get back to the base call after forwarding the base call to another extension also use R+1. | ||
Line 55: | Line 48: | ||
R+1 - disconnects current call and return back to base call | R+1 - disconnects current call and return back to base call | ||
To switch between two established call connections use: | To switch between two established call connections use: R+2 or press R-key twice – change between call 1 and call 2 | ||
R+2 – change between call 1 and call 2 | |||
To transfer the base call to another call extension use: | To transfer the base call to another call extension use: R+4 – transfers call 1 to call 2 | ||
[[Category:Howto|{{PAGENAME}}]] | [[Category:Howto|{{PAGENAME}}]] | ||
Latest revision as of 11:47, 26 October 2021
The IP1200 & IP1202/IP1203 could enable or disable the R-Key handling which is necessary for transferring calls.
Applies To
This information applies to
- IP1200, IP1202, IP1203
- IP21, IP22, IP24, IP28, IP29, IP302, IP311, IP411 - Analog Phones
- IP110 in hands-free mode
Build V6 and later
More Information
Problem Details
Unknown flash codes for transferring, holding or changing between calls.
Configuration
Enable the “local R-key handling” at the DECT-base in DECT/Config/System .
Usage
To use the R-key functions press the R-key during a call followed by the appropriate number.
A single R-key press sets the first call on hold.
Use the following codes:
- 0 – reject call waiting
- 1 – disconnect held call
- 2 – change between call 1 and call 2
- 3 – 3-party (3PTY) conference (if supported)
- 4 – transfer call 1 to call 2
e.g. incoming call, transferred to another extension.
- accept incoming call
- press R once
- dial the second extension
- press R2 to change between call 1 and call 2 or press R-key twice
- press R4 to transfer both calls
To get back to the base call after pressing R-Key use: R+1 - return back to base call after pressing the R-Key
To get back to the base call after forwarding the base call to another extension also use R+1.
R+1 - disconnects current call and return back to base call
To switch between two established call connections use: R+2 or press R-key twice – change between call 1 and call 2
To transfer the base call to another call extension use: R+4 – transfers call 1 to call 2