Reference15r1:Concept IP29-20

Applies To

This information applies to

• innovaphone IP29-20

Overview

innovaphone IP29-20 is an IP adapter for twenty analogue interfaces (FXS).

It includes 20 interface licenses upon delivery.

Requirements

• Firmware 13r1sr11
• innovaphone PBX with appropriate amount of Port<v> Licenses
• Power over Ethernet+ supply according to IEEE 802.3at, Class 4 (PoE+)
• appropriate adapter cable - see below

Configuration

Connection

As different cabling concepts might be applied, innovaphone does not deliver any connection cables with the system.

Note: Below mentioned 3rd-pty-products are subject to change and there might be alternative products of other manufacturers/resellers.

Find below a list of possible connection concepts and their realisation:

PinOUT

Built-in 8P8C connectors provide following pinout:

Pin	Function
1	RING-2
2	TIP-2
3	RING-3
4	TIP-1
5	RING-1
6	TIP-3
7	RING-4
8	TIP-4

This pinout is especially designed for use with twisted-pair Ethernet patch cables

Direct terminal connection

In case of direct connection of analogue terminals by use of 2-wire-a/b-connectors RJ-11 / modular jack 6P2C, a special adapter has to be used.

This adapter has to distribute above mentioned IP29-20 pinout to four 6P2C connectors using the pinout below:

Pin	Function
3	TIP
4	RING

Next to own assembling, below listed are some 3rd-party-products (information is subject ot change):

• LogiLink-Adapter
• L-Com-Adapter

Patch-panel based connection

In case of patch-panel based connection, used adapter cable depends on used patch panel:

• patch-panel with 8-wire-connectors (8P8C): use twisted-pair Ethernet patch cables
• patch-panel with 2-wire-connectors (8P2C): use of an adapter cable splitting up 8P8C to 4 x 8P2C.

For the 2nd option, innovaphone offers a quadruple adapter cable, order-no. 03-00029-001. To connect all 5 interfaces of IP29-20, five of those adapters have to be used. Lenght: 180 cm

Provisioning

IP29-20 is added to an existing V13-PBX-system by execution of V13-installer upon initial device startup.

Analogue extensions connected to IP29-20 are bound to the innovaphone PBX by use of the V13-device-provisioning.

Within UserAdminAPP/RegisterPhones, unique provisioning code are generated for dedictated users.		At PBXManager/FXS-Plugin, IP29-20 device can be selected as FXS-adapter and offers 20 TEL-interfaces for configuration. Previously generated provisioning codes can be assigned to each TEL-interface.

If an appropriate number of Port<v> licenses is available in the corresponding innovaphone PBX,
the registration of analogue terminals to the selected users takes place immediately after the provisioning is confirmed.

Restrictions

• In case of Class3-PoE power supply (no PoE+), the first eight FXS interfaces (1-8) are available within the device.

Technical data and variants

Datasheet IP29-20

Variants

Single Device

• 1 x IP29-20
• 20 x FXS-hardware-interface licenses included
• Order no. 01-00029-007

Single Device w Licenses

• 1 x IP29-20
• 20 x FXS-hardware-interface licenses included
• 20 x FXS-Registration-Licence* included
• Order no. 88-00010-124

Bundle

• 2 x IP29-20
• 1 x 19-inch mounting frame 1U for 2 devices
• 40 x FXS-hardware-interface licenses included
• Order no. 88-00010-093

Bundle w Licenses

• 2 x IP29-20
• 1 x 19-inch mounting frame 1U for 2 devices
• 40 x FXS-hardware-interface licenses included
• 40 x FXS-Registration-Licence* included
• Order no. 88-00010-124

Note to FXS-Registration-Licences*

• These licenses enable a PBX-registration of FXS-devices on behalf of the user
• These licenses are bound to the dedicated IP29-20 device. Surplus licenses can not be used at other devices for PBX-user-registration.

Related Articles

• Reference11r1:Interfaces/FXS/Physical
• Maximum wire length