Howto:How to Reset IPXXX

Summary

Different Reset Options of IPXXX

Applies To

This information applies to

• All innovaphone products with the latest boot code.

More Information

Different options resetting innovaphone devices.

• bringing to Factory default
• bringing to TFTP mode for GWLoad
• clearing config
• explaining the Led behavior

Additional Information for the following table, TFTP-Mode or TFTP-Mode + FACTORY RESET for the phones IP110, IP150, IP200, IP202, IP230

Seperating the phone from the power, press the Key/Button, keep on pressing the Key/Button, plug in the PSU or ethernet cable (in case of PoE), watch the status of the device (table: visual display), release the Key/Button after time shown in the table.

Device (visual display)	Reset Button/key	Button pressed	Clear Config Firmware Boot code update	Pressing Button to TFTP without deleting config in seconds ca.	Pressing Button to factory reset in seconds ca.	GWLoad- / TFTP-Mode	Firmware starting	Firmware ready	Firmware Error
IP21 (all LEDs)	Button	ready: <5s blink, >5s constant flash line1+ line2 + door + aux constant flash / link + act off with plugged in Ethernet cable 100M + link: <3s off, >3s normal operating state	... ready fast blink, line1 + line2 + door + aux off link + 100M normal operating	3	25	all Led’s are constant flashing Link is blinking	ready + line1/2 + door+ aux + 100M(if link) permanent for ca. 5s link blinking	ready + 100M (if link) link blinking
IP400 (all Led’s)	Button	PPP+Tel.1+Tel.2: < 5s blink, [5;8] constant flash, >8 ready + link + act constant flash without Ethernet cable plugged in: <8s off, 8s one blink, >8s off		3	25	Ready + Link + Act flashing constant	<8 Ready + PPP + Tel1 + Tel2 constant flash, [3;10] link + act. uncoordinated flashing >10s Ready + link (if link) constant act. blinking	Ready + 100M (if link) link blinking
IP3000 (all Led’s)	Button	<6s PRI1+PRI2+S/T+ready blink, [6;10] PRI1 + PRI2 + S/T + ready constant flash, act + speed + link off >10s PRI1 + PRI2 + S/T constant flash, ready + act + speed + link off with Ethernet cable plugged in: act + speed + link normal working state	Fast blink (green)	3	25	all Led’s flashing permanent ready off link blinking	>2 link + speed constant flashing, act blinking <5s PRI1 + PRI2 + S/T constant flash >5s ready constant flash, (if link) link + speed constant flashing, act blinking	ready constant flash, (if link) link + speed constant flashing, act blinking	Blinking (green)
IP800 / IP6000 (red/green/orange ready LED )	Button	<6 slow gn blink [6;10] constant red [10;13] fast gn blink <13 constant orange	Fast blink (green)	3	15 (IP800) 15-20 (IP6000)	constant orange	Red	Green	Blinking (red)
IP1200	Button	<2s Alarm red constant flash, ready off [2;7] Alarm off, ready slow green blink [7;13] Alarm off, read fast blink green >13s Alarm off, ready 2 Hz blink green	Fast blink	3	10	Slow flash ca. 2 Hz	<2s Alarm red constant flash ready green constant flash Power orange constant flash [2;4] Alarm off, ready off, Power orange >4s Alarm off, ready constant green flash, Power constant green flash	Ready constant green flash and power constant orange flash	Alarm (red)
IP200/IP202 (red handset)	Alt key	Slow blink	Slow blink	3	5	Constant flash	Slow blink	Off	Constant flash
IP200A/IP210 (red handset)	Alt key	Slow blink	Fast blink	3	15	Slow flash ca. 2 Hz	On	Off	Blinking
IP230 (Menu key)	Menu key	Slow blink	Fast blink	3	10	Slow flash ca. 2 Hz	On	Off	Blinking
IP110 (Led’s in F1-F4 key)	Save key	Slow blink	F1-F4 off	3	10 - 15	Slow flash ca. 2 Hz	constant F1 flash	Off	Blinking

Related Articles

Howto:How to use gwload